限制復制準則 的英文怎麼說

中文拼音 [xiànzhìfùzhìzhǔnzé]
限制復制準則 英文
replication filters
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 復 : Ⅰ形容詞1 （重復） repeated; double; duplicate 2 （繁復） complex; compound Ⅱ動詞1 （轉過去或轉過...
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 則 : Ⅰ名詞1 （規范） standard; norm; criterion 2 （規則） regulation; rule; law 3 （姓氏） a surname Ⅱ...
  • 限制 : place [impose] restrictions on [to]; astrict; restrict; limit; confine; shut down on [upon]: 限制...
  • 準則 : norm; standard; criterion; rule; formula; square
  1. The entire mathematical model of structure optimization of dairy housing was set. computer programs were made with finite - element method and full - stress method. some typical cases were drawn up and checked out to prove that the program was reliable

    建立了牛舍結構優化的數學模型，利用有限元法和滿應力準則法編制了程序，並用典型算例對程序進行了反復考核，證明了程序的可靠性。
  2. 2. a relevant formula of eight - node adhesive finite element is deduced in the paper, which is based on a separately interpolation scheme for reissner - mindlin plate element. a load capability analysis method for patched composite laminated structure is established by using tsai - hill failure criterion and thai ' s reduced stiffness scheme, and corresponding computer code is also developed

    在任意四邊形四節點復合材料層合板殼單元的基礎上，推導了相應的八節點膠單元，並採用蔡-希爾強度理論以及蔡氏剛度退化準則，對復合材料層合板膠接補強結構進行剛度分析和極限承載能力分析，編制了相應的有限元分析程序。
  3. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  4. And then, according to finite element theory of reinforced concrete, the main calculating program of " nonlinear finite element ultimate analysis of reinforced concrete thin slabs with complex geometry & boundary condition " is made by using the triangle layered - assembled element of elastic thin slabs and the stress - strain relation by considering concrete as anisotropic material under effecting by two - way stress, and the concrete material model presented by darwin and pechnold, and the yield criterion of concrete presented by kupfer and gerstle

    然後根據鋼筋混凝土有限元理論，以三角形分層組合式的彈性薄板彎曲單元為基礎，考慮混凝土為各向異性材料在雙向應力作用下的本構關系，採用darwin和pechnold的混凝土材料模型和kupfer與gerstle等人研究的混凝土破壞準則，編制了「復雜幾何形狀和邊界條件鋼筋混凝土薄板非線性有限元極限分析程序」中的核心計算程序。
分享友人
分享到 Line

分享到臉書