限度變分 的英文怎麼說

中文拼音 [xiàndùbiànfēn]
限度變分 英文
constrained variation
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 限度 : limit; limitation; measure; tether
  1. The calculation modes of the coefficient of shrinkage and creep of the bulgy core concrete in steel tube are discussed. based on a few reasonable hypotheses and the stress - strain relation of concrete acquired by the " adjusting valid modulus depending on load time " method, a compact formula is reasoned out, which is applied to calculate the equivalent elastic modulus of the bulgy core concrete considering the affection of shrinkage and creep. so, the analysis of the affection on cfst arch bridge by shrinkage and creep can be progressed by pole - girder fem, further more, the analysis precision is quite high

    本文還對核心膨脹混凝土特殊的收縮、徐變系數計算模式展開了探討，在合理的假設前提下，採用「齡期調整的有效模量法」得到的混凝土的本構關系，推導出鋼管內核心混凝土在考慮徐變影響后的等效彈性模量計算公式，並以此為基礎採用桿系有限元方法來對鋼管混凝土拱橋進行較高精度的收縮徐變分析。
  2. On the basis of the hamilton ' s principle, the element mass matrix, stiffness matrix, and damping matrix caused by coriolis force of the finite method for the conveying fluid tubes were educed in the paper

    本文用哈密頓變分式推導輸送流體管道的有限元法分析單元質量矩陣、剛度矩陣和科里奧利力引起的阻尼矩陣。
  3. On the basis of the others, according to the constructional feature of the constitution of the composed soil nails, the computation mode of the he strut frame made of composed soil nails was set up to analyze the distortion of the he strut frame made of composed soil nails when it is stressed. with the engineering data, the strut frame made of composed soil nails is analyzed with the program ababqus, and the effects of the distortion characters, the property of the deposition of the ground, the mechanical property of the soil nails, the variation of the length and the separation of the soil nails, and the diametric of the mixing piles on the strut frame made of composed soil nails, and the distortion property of the strut frame made of composed soil nails under different ground conditions

    在總結前人的研究成果下，針對復合土釘墻構造的特點，建立了模擬復合土釘墻受力變形的計算模型，並結合工程實測資料，運用大型通用有限元程序ababqus對復合土釘墻進行了有限元分析，詳細討論了復合土釘支護結構開挖過程中的變形特性、地面沉降性狀、土釘受力性狀；土釘長度變化、土釘間距變化、攪拌樁樁徑變化對復合土釘支護結構的影響；復合土釘支護結構在不同地基條件下的變形特性。
  4. This paper, takes rli as an object of study, takes property rights relationship and management relationship of rural land as a main clue, takes raising the management benefit into full play of rural land and ensuring rural land sustainable utilization as objective, uses the theory of western institution economics and market economics for reference, adopts the method of study of combining macro analysis with microanalysis and combining quantitative analysis with qualitative analysis, reviews systematically the developing process of rli in china since the founding of our country and the developing tendency of rli in the world, summarizes the influence law of rli to rural land management benefit, analyses the innovative mechanis m. institutive achievement and being faced with difficult position and gauntlet of the present rli in china, and defines the objective and following principles of rli innovation proceeding from the actual conditions of our country. on the basis of these, constructs the innovative models by stages of rural land property rights institution and management institution, which accords with the market economic law and the law by stages of rural economic developing levels and gives consideration to efficiency and fair

    本文以農村土地制度為研究對象，以農村土地的產權關系和經營關系為主線，以農村經濟發展水平（包括農村生產力發展水平和農村工業化、城鎮化水平）和農民的承受能力為依據，以最大限度地提高農地經營效益、確保農地資源的可持續利用為目的，借鑒西方新制度經濟學理論和市場經濟理論，採用宏觀分析與微觀分析、定量分析與定性分析、規范研究與實證研究相結合的研究方法，系統地回顧了建國后我國農地制度的演變過程及世界農地制度的演變趨勢，總結了農地制度對農地經營效益的影響規律，分析了我國現行的家庭承包經營責任制的創新機理、制度績效及其面臨的困境與挑戰，並從我國的實際出發，確定了農地制度創新的目標及應遵循的原則，在此基礎上構建符了符合市場經濟規律和農村經濟發展水平的階段性規律、兼顧效率和社會公平的階段性農地產權制度創新模式及其對應的經營制度創新模式。
  5. ( 6 ) in this paper. adopting fea software ansys to simulation and analysis the al ecap process. in order to spread out studying of ecap in the future. the results show : die comer angle, the radius of round angle, the friction coffience of workpiece and die, the properties of die ( elastic modulus, possion ratio ) et al, have some degree impact on the deformation of materials

    （ 6 ）採用有限元（ fea ）分析軟體ansys對al的擠壓過程進行ecap模擬與分析，為后續研究工作做好鋪墊，分析結果表明：外切角、圓角半徑、試樣與凹模之間的摩擦系數、凹模本身的特性（如彈性模量、泊松比等）等等，對材料的變形量都由不同程度的影響。
  6. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  7. The number of modes should be selected according to the participant coefficient of mode when calculating the internal force by the response spectrum method ; ( 4 ) the roof plate of large base which connect the towers together should be thick enough but not exceeding the proper scope that the towers and the large base can vibrate together, ( 5 ) in structures with large base and muti - towers, with increasing of the capacity of the large base, the inter - story shear force will increase while the inter - story displacement will decrease as to fulfill the ductility request to avoid the large base becoming weak story, but meanwhile, the upper story will turn into weak story, thus the coefficient r s should be within 2. 0 ~ 3. 0

    採用振型分解反應譜法計算結構內力時應根據振型參與系數選擇振型避免漏選；大底盤多塔樓結構連接各塔樓的裙房屋面剛度應做得大些，以保證底部裙房與上部塔樓共同振動，但也不能過剛；大底盤多塔樓結構底盤承載力的加強將使底盤層剪力增大、層間變形減小，但易於滿足延性要求，在一定程度上可避免底盤成為薄弱層。但底部加強會導致薄弱層的上移，因此採取提高底盤承載力的措施的效果是有限度的，承載力系數s宜取為2 . 0 3 . 0之間。
  8. In this paper, the course of isothermal crystallization kinetics of polymer in limited volume unit is simulated by use of the method of monte carlo. four factors influenting on the course of polymer in the limited volume unite isothermal crystallization are analyzed under the given conditions. the four factors are sample volume shrinkage, the change of the linear growth rate of entities g, the change of sample thickness and the change of the number of nuclei

    本文採用montecarlo方法研究了高聚物在有限體積元中的等溫結晶動力學過程，分析了在一定條件下，樣品體積收縮、晶體線生長速率變化、樣品厚度變化和晶核數目變化這四種因素對高聚物在有限體積元中的等溫結晶過程的影響。
  9. According to finite element segmentation principle, by combining test with observation, the author has measured the air streamline and speed distribution of burning equipment in dally situation, which provides some guide for research of air field in hearth on cold and hot conditions. and the law is found of air speed distribution by measuring its speed and distribution of upper and lower deck on cold condition, thus it lays the foundation for analysis on hot condition. under four burning states, we measure the air speed in single, double - deck, and find out its corresponding distribution law

    5 .根據有限元分割原理布置測點，採用降溫方法，用k五江9106等儀器分別測出單雙爐排燃燒方式4種不同工況下，該燃燒設備爐膛內coz 、 02 、 co氣體濃度，並找到了隨爐膛高度方向及深度方向變化規律;從燃燒原理分析評價了2種燃燒方式爐膛內coz 、 02 、 co氣體濃度場分佈特點及相應燃料層內乾燥、干餾、氧化、還原、灰渣層厚度，肯定了雙層爐排燃燒方式爐膛中c02 、 02 、 co氣體濃度場分佈合理性，從燃燒理論找出了最佳濃度場分佈狀態及燃料層內各反應層厚度。
  10. Using large - scale current finite element software algor, the author builds 3d finite element models for the five project, and analyzes flexural, temperature deform and natural frequencies of the five guideway girder projects

    運用大型通用有限元分析軟體algor ，對五種可能軌道梁結構方案建立有限元空間分析模型，進行撓度、溫度變形及自振特性的對比分析。
  11. In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer

    本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程，從鋪裝層環境溫度變化范圍、交通量等使用條件出發，在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上，提出了（即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma ）的高性能鋼橋面sma鋪裝體系，並對這種sma的組成材料，包括改性瀝青、集料、礦粉、纖維進行了比較研究，設計了這種sma的配合比，對sma混合料的性能進行了對比試驗，對這種sma方案進行了疲勞性能研究，驗證了所選擇sma方案的可行性。
  12. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  13. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  14. Creep analysis methods of high - rise buildings and large span buildings can only refer to creep coefficient method in bridge engineering or the method of degree of creep in hydraulic construction engineering under the present experiment conditions. in this paper, the incremental expressions of concrete creep and shrinkage strain when the initial computational age is not the same as the loading age are derived and corrected from the concept of concrete creep coefficient and the mean value theorem of integral and the principle of superposition. the differences of efficiency and accuracy of creep analysis between the finite element method with creep coefficient and the initial stress method with degree of creep are presented. this paper suggests that engineers should use the initial stress method with degree of creep to estimate the influences of creep on high - rise buildings and large span buildings on the basis of conceptual design

    基於現有的試驗資料，高層及大跨度民用建築的徐變分析只能參照橋梁結構中的徐變系數方法或水工結構中的徐變度方法進行.從徐變系數的定義出發，利用積分中值定理和疊加原理，推導並修正了加載齡期與起算齡期不同時徐變收縮應變增量的表達式，對比了應用徐變系數分析徐變的有限元法和應用徐變度分析徐變的初應變法在效率和精度上的差別，並建議應從概念設計的角度出發，採用徐變度的初應變法來估算徐變對高層及大跨度民用建築的影響
  15. Abstract : creep analysis methods of high - rise buildings and large span buildings can only refer to creep coefficient method in bridge engineering or the method of degree of creep in hydraulic construction engineering under the present experiment conditions. in this paper, the incremental expressions of concrete creep and shrinkage strain when the initial computational age is not the same as the loading age are derived and corrected from the concept of concrete creep coefficient and the mean value theorem of integral and the principle of superposition. the differences of efficiency and accuracy of creep analysis between the finite element method with creep coefficient and the initial stress method with degree of creep are presented. this paper suggests that engineers should use the initial stress method with degree of creep to estimate the influences of creep on high - rise buildings and large span buildings on the basis of conceptual design

    文摘:基於現有的試驗資料，高層及大跨度民用建築的徐變分析只能參照橋梁結構中的徐變系數方法或水工結構中的徐變度方法進行.從徐變系數的定義出發，利用積分中值定理和疊加原理，推導並修正了加載齡期與起算齡期不同時徐變收縮應變增量的表達式，對比了應用徐變系數分析徐變的有限元法和應用徐變度分析徐變的初應變法在效率和精度上的差別，並建議應從概念設計的角度出發，採用徐變度的初應變法來估算徐變對高層及大跨度民用建築的影響
  16. At last but not the least, integrating with china ' s reality the paper analyzes whether there are financial risks or not in economic structure, foreign debt management, foreign exchange system selection and foreign exchange level. in face of the changes from domestic and outside circumstances, we should carry out the reform steadily, strengthen financial regulation, prevent and defuse financial risks so as to provide better banking services for economic development and social stability

    最後，結合中國國情，本文詳細分析我國在經濟結構、外債管理、匯率制度選擇和匯率水平安排方面是否存在金融風險隱患，以及針對我國國內國外經濟發展環境的改變，我國應如何進行改革調整，以便最大限度的抵禦風險、防範危機，使金融能夠更好的發揮其促進經濟發展、穩定社會秩序的作用。
  17. But they are very sensitive to image noise and points delocalization error. in order to use the invariants, the local geometric constr aint must be added

    但同時，由於興趣點的局部灰度差分不變量對噪聲及點位置偏差很敏感，所以在做實際圖像匹配時必須加上局部幾何限制。
  18. This research concludes that technology resistance, market progression, and environment influence are the three major forces that affect the difusion of product appearance and dominate, respectively, the development of stylability curve in terms of altitude change, lateral extension, and overall performance and the starting point of an emerging curve

    本研究發現技術限制力、市場發展力和環境影響力，為影響造形擴散之三大主要影響作用力，分別影響造形力曲線發展之垂直高度變化、水平長度延伸，以及整體曲線之起伏和新曲線之起始位置。
  19. The results of the experiment are in good agreement with the data of theoretical calculation and the actual conditions of earthquake calamity. these data and information give a convenience for the following work. the finite element analysis ( fea ) has been completed within the environment of ansys

    有限元分析主要以ansys為工具對煙囪進行了動應力計算，得出了在不同地震波水平和豎向激勵下動應力隨高度分佈情況，並據此繪制了動應力隨高度變化曲線圖。
  20. The curves of the consolidation settlement in soft clay base of flood land are gained, which compare the effect of sand drain. the settlement - time curves in different period are also gained, which increase the height of embankment to 8m, based on the test data of hang - yong highway. furthermore, the consolidation settlement characters of these entity engineering are analyzed, and, the variation rules of the rate of grade and degree of the curves in different period in the whole section, the maximal settlement and the liner regression relations between the rate of grade and degree are calculated

    本文利用大變形固結有限元分析程序（ lscfea ）中的小變形平面固結分析單元（ sse2 ） ，結合實體工程項目進行了地基固結沉降的有限元計算，分別得出河灘相軟土地基在考慮砂井和未考慮砂井作用下的固結沉降曲線及杭甬高速公路試驗段在高堆載情況下的固結沉降曲線；並對以上曲線特徵進行了分析，得出各時間段曲線斜率、角度在整個斷面的變化規律，以及沉降最大值與斜率、角度變化之間的線性回歸關系。
分享友人
分享到 Line

分享到臉書