階梯形基礎 的英文怎麼說
中文拼音 [jiētīxíngjīchǔ]
階梯形基礎
英文
benched foundation-
Take integrity of object information into condition, a two - dimension signal processing method which can make a measurement of the target ’ s speed as well as the range is brought forward at the basis of waveform parameter design. and simulation in the background of hf multi - object with noise is taken. a comparison of signal properties, processing and antinoise detection performance is taken between mcpc and another two high range resolution radar signals : single carrier pulse coded signal and step frequency pulse coded signal
考慮到目標信息提取的相對完整性，以高頻雷達為背景，在對多載波相位編碼脈沖串信號參數設計的基礎上，推導了三種多載頻相位編碼脈沖串信號的距離速度二維處理過程並相應的對多目標噪聲環境進行了模擬;將多載波相位編碼信號與另外兩種距離高分辨信號:單載頻相位編碼信號和相位編碼階梯跳頻信號，在信號特性、處理過程和抗噪聲特性方面進行了對比;本文從理論上為多載波相位編碼信號的波形設計和分析、信號的處理打下基礎。The necessary condition has been obtained on forming rolling workpiece surface defect by means of upper - bound method and least energy principle
以此為基礎，並藉助于上限原理和最小能量原理，獲得了楔橫軋成形階梯軸時軋件表面缺陷形成的必要條件。Biology, etc. owing to many merits has not yet been used to measure parameters of gratings. the paper researches on the subject in view of current lack of it. the main tasks of the paper include : analyzing ellipsometric characteristics of gratings in detail with vector diffraction theory and ellipsometrics ; devising a reflective quarter wave plate at normal incidence according to some ellipsometric characteristics ; making use of normal simplex algorithm during ellipsometric inversion of gratings parameters, inversing ellipsometric parameters with gaussian noise of different standard deviations to simulate actually measured values with examples of isotropic metallic and anisotropic step gratings and testing that ellipsometry about gratings parameters is feasible with the range of certain precision ; discussing choice of incidence angle at length
本論文的主要工作包括：結合光柵的矢量衍射理論和薄膜的橢偏理論，詳細分析了光柵的橢偏特性；並且根據一些橢偏特性設計出一款正入射反射型單波長1 4波片；在光柵參數的橢偏反演中，引入正單純形法作為反演演算法，分別以各向同性的正弦形金屬光柵和各向異性的階梯型光柵為例，在標準橢偏值的基礎上加入不同偏差的高斯噪聲來模擬實際的橢偏測量值進行反演，在一定精度范圍內得出滿意的光柵參數，說明光柵參數的橢偏測量是可行的；還就入射角的選取問題進行了一定的探討。So such kind of diseases can be forecasted through qst. first, the physiological basis of vpt is introduced. then the thesis discusses in detail the psychophysical knowledge of the threshold detecting method, especially the transformed - rule up and down method and forced - choice method
本文首先介紹了定量振動感覺測試系統的生理學基礎，接著對閾值檢出演算法的心理物理學基礎進行了詳細的敘述，著重介紹了系統採用的變形階梯法同強迫選擇法相結合的演算法。As the basis of stochastic torsional analysis, a stepped thin - walled beam model with complex cross - sections of arbitrary shapes ( open, closed or mixed ) is established in this paper, which takes into account the effect of secondary shear flow resulting from warping restraint
摘要具有復雜斷面形狀的階梯精密梁模型作為扭轉隨機分析的基礎，可以計及翹曲約束引起的二次剪流。Based on the experiment and analysis, the optimum conditions for preparation of si02 films have been studied. furthermore, using the inverse designing idea of fgms, fe / mo and mo / sio2 fgms have been successfully prepared. finally, the composition and microstructure of the materials have been measured by x - ray debey powder diffraction ( xrd ), x - ray photoelectron spectroscopy ( xps ), scanning electon microscope ( sem ), step instrument and metallgical microscope
在系統實驗的基礎上探討sio _ 2薄膜沉積工藝條件及其影響因素，獲取了sio _ 2薄膜的最佳工藝條件；採用功能梯度材料（ fgm ）的逆設計思想，在最佳沉積條件的基礎上成功制備出fe mo和mo sio _ 2功能梯度材料，並以x射線衍射， x射線光電子能譜，電鏡掃描，膜臺階儀，金相顯微鏡等手段對材料進行成分測定和表面形態結構分析。Continuous - time analog filter is the only method when processing high frequency signal ( usually above 1mhz ) in low power consumption. it has been widely used in the area of communication, electronic measurement, instruments, autocontrol, etc. it ’ s especially used in digital and analog mixed signal processing and communication integrated circuit. current - mode filter becomes the new research direction in the world, as it ’ s high speed, low power consumption and simple configuration
提出了基於ota的多功能電流模式雙二階濾波器，基於ota的八階切比雪夫濾波器，用模擬lc梯形電路法設計橢圓低通濾波器時，在傳統的狀態變量選取方法的基礎上，用改進后的狀態變量選取方法得到了（ k + 1 ）階橢圓函數低通濾波器的簡化信號流圖，實現了簡化的基於ota的橢圓低通濾波器電路。In the paper, theoretical analysis method is applied to analyze the endured force of these important regions, determine the style of forming in these regions and reveal the technological characteristic of the forming of stepped tubular part. it is the first time to divide the one - off drawing of stepped tubular part into two stages from the forming mechanics theory. by these methods, it established the basis in determining the forming law of one - off drawing
並採用理論分析方法，全面地分析了幾個重要區的變形和受力情況，確定了這些區的變形方式、變形特點、變形性質，揭示了階梯筒形件的成形工藝特點，首次從變形力學理論的角度將階梯筒形件的一次拉深成形過程分為兩個階段，為確定其一次拉深成形的規律奠定了基礎。分享友人