零件孔組件孔 的英文怎麼說

中文拼音 [língjiànkǒngzǔjiànkǒng]
零件孔組件孔 英文
component hole
  • 零 : Ⅰ數詞1 （零數） zero2 （數的空位） zero sign （0）; nought 3 （表示沒有數量;無） nil; nought 4 （...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 零件 : [工業] part; element; detail; component; finding; section; spare part; spare; fitting; ancillary...
  • 組件 : assembler
  1. Measures to locate reference points, and drills and taps holes as needed to mount assemblies, components and parts, using hard tools and power tools

    測量定位參考點位置，根據安裝裝配、組件和零件的所需進行鉆孔和打洞。會使用機械工具和電力工具。
  2. The electron gun and coil inside the display will produce temperature, therefore are ventilate holes to dispel the heat on left and right sides and the above of the chassis. please try to prevent the dust from invading. too many dusts will cover electronic part and influence the heat dissipation, which will reduce the life - time of the spare parts

    顯示器因電子槍及線圈連續運作而會產生溫度，所以在機殼的左右及上面都會有透氣孔散熱，應盡量避免灰塵侵入，因為過多的灰塵覆蓋在電子零件上，會影響散熱效果，降低零組件的壽命。
  3. In view of the problems in the design of the large andmedium - sized indoor substations built by guangzhou power bureau in recent years, points for attention in the design of indoor substations are expounded in terms of ventilation, cable channel, reservation of hangers and space for transportation and installation, ground wire, lighting for the whole substation, etc

    僅僅推力頭軸、孔存在間隙時，推力頭其它零件製造質量與安裝質量達到設計要求，是不會影響精確徑向定位的.爾王莊泵站9機組出現的環鍵與平鍵斷裂情況，可能不是由軸、孔間隙過大引起，而是其它尚未查明的原因
  4. With focus on high volume quality products, neco has carved a solid foundation in the headset and bottom bracket component areas. in addition to machine tooling capacity that covers a wide range of applications and finishes, neco also has extensive capabilities of alloy cold forging, steel press, hole taping and cnc finishing, neco delivers on the promise of providing competitive products at high volumes

    帶著高品質的產品，志慶在車頭碗組及五通碗組的零件領域創建了一套完整的體系，在鋁合金冷鍛，鋼鐵沖壓，鉆孔及cnc加工方面擁有很強實力，能確保提供高檔次的有競爭力的產品。
  5. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
  6. The iron core of the product is annular. the secondary winding go uniformity around the core. the clip clamps the core

    本型零序電流互感器的鐵心為環形，二次繞組均勻繞制在鐵心上，用夾件夾緊鐵心，夾件備有安裝孔。
分享友人
分享到 Line

分享到臉書