零壓電阻 的英文怎麼說
中文拼音 [língyādiànzǔ]
零壓電阻
英文
zero voltage resistance-
1 m 0. 5, the phase - shifted angle 6 is controlled in term of sine law which makes the magnitude of resonant voltage track a reference sine voltage, and the resonant voltage is rectified, filtered, inverted and then the better sine - voltage output is obtained, theoretical analysis and experimental results show that for the resistive load and inductive load, the switches of leading leg of the phase - shift - controlled circuit are always turned on at zvs, and ones of lagging leg are turned on at zvs ( < 0 ) or turned off at zcs ( ( > 0 ), moreover, all switches in the low - frequency inverter are always turned on and off at zvs, the measured circuit efficiency for rated load reaches up to 88 %
從功率單向流動角度出發，提出了一種lcc諧振型恆頻移相單相高頻鏈逆變電路拓撲，在調制系數0 . 1 m 0 . 5情況下，控制移相角按正弦規律變化，使諧振電壓脈沖列的幅值追蹤參考正弦電壓信號，經過整流、濾波、低頻逆變，從而獲得正弦度較好的輸出電壓。理論分析和實驗結果證明對于阻性負載或阻感性負載，移相全橋具有超前橋臂零電壓開通，滯后橋臂或者零電壓開通（ _ 0 ）或者零電流關斷（ _ 0 ）的軟開關特性，而低頻逆變器的各個開關均實現零電壓條件下的開通與關斷。For multi - infeed hvdc systems, when the minimum eigenvalue of the system becomes zero, the voltage stability graph can be plotted effective short circuit ratio as function of coupling impedance
對于多饋入hvdc系統，在最小特徵值為零的情況下，可以根據這種關系作出有效短路比?連接阻抗圖，即電壓穩定圖。Abstract : in this study, 2618 aluminum alloy manufactured by spray process was heated in a heating furnace, and the microstructures were investigated. by the process of heating in a heating furnace and then squeeze - forming, one component of the motorcycle was produced successfully with the semi - solid aluminum alloy
文摘:採用電阻爐加熱的方法對噴射沉積法制備的2618鋁合金進行了二次加熱實驗，觀察了顯微組織的變化；並通過電阻爐加熱、半固態擠壓鑄造的方法成功地試制了摩托車零件。Unified power flow controller ( upfc ) is one of the most powerful and most promising controllers of facts. if we use upfc to control the transmission parameters, terminal voltage, line impedance and phase angle in normal situation and use it to compensate zero sequence and negative sequence currents when one of transmission lines is cut off, we can implement two phases operating in high voltage transmission lines, which can improve stability and reliability for the transmission system
統一潮流控制器（ upfc ）是功能最強、最具發展潛力的靈活交流輸電系統（ facts ）控制器之一，如果在常規條件下，用upfc實現輸電線路的電壓調節、移相、潮流控制、阻尼振蕩等功能，在發生單相永久性接地或單相斷路故障時，由傳統的三相跳閘改為單相跳閘，用upfc的並補來濾除兩端系統的零序和負序電流，用upfc的串補來提高輸電線的傳輸功率，以實現兩相長期運行，那麼輸電系統的穩定性、可靠性將大大提高。Remember the following words and expressions : e. g. multimeter ； circuit ， current ； voltage ； resistance ； digital multimeter ； analogue multimeter ； analogue multimeter scales ； zero adjustment control ； zero adjustment control for resistance ranges ； measurement ranges switch ； transistor test socket ； meter probe ； positive terminal ； negative terminal ； anode ； cathode ； red lead ； black lead ； power supply ； connect in parallel ； connect in series
記住萬用表、電路、電流、電壓、電阻、數字萬用表、模擬萬用表、表頭、機械零位調整器、歐姆零位調整器、量程選擇開關、晶體管插孔、表棒、正接線端、負接線端、陽極、陰極、紅導線、黑導線、電源、並聯、串聯等常用英文單詞，並逐步掌握。By compared with the simulation results and the experiment results, we come to the conclusions that : ( 1 ) circuit with assistant network can widen soft - switching extent in lagging arm, reduces duty - cycle loss on the secondary, diminishes switching dissipation of inverter spot - welding power source. ( 2 ) the range of resonant capacitor, the important factor to soft - switching process, not only affects zero - voltage turn - off of power switches, but also affects the range of zero - voltage turn - on of power switches. so resonant capacitors must be considered according to many aspects ; ( 3 ) it easily fulfils soft - switching condition in lagging arm as leakage inductance of power transformer increases, but bigger leakage inductance of power transformer increases opening dissipation of transformer and decreases efficiency of soft - switching inverter power source
通過模擬結果與軟開關點焊逆變器試驗結果的對比分析，得到了如下主要結論：採用輔助網路可以完全拓寬全橋軟開關逆變器的滯后橋臂軟開關范圍，減小了次級占空比丟失，降低了逆變電阻點焊電源的開關損耗；諧振電容是影響軟開關工作狀態的重要因素，其大小不僅影響開關管的零電壓關斷，同時也影響開關管的零電壓開通范圍，因此，諧振電容應該綜合考慮；功率變壓器漏感越大，越容易滿足滯后橋臂的軟開關條件，但是大的漏感也使變壓器的通態損耗增加，降低了軟開關逆變器的效率。The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。The sensor offset is governed by its thermal drift, electric drift and time drift, so eliminating the offset thermal drift in the measurement of sensor needs to keep the values of resistance and temperature coefficient for different resistor strips to be equal each other
壓力傳感器的零點存在熱漂移、電漂移和時間漂移，減小壓力傳感器的熱零點漂移的措施是各力敏電阻的電阻值及其溫度系數的相等性。The sensor offset is governed by its thermal drift, electric drift and time drift, so eliminating the offset thermal drift in the measurement of sensors requires to keep the values of resistance and temperature coefficient for different resistor strips to be equal each other
壓力傳感器的零點存在熱漂移、電漂移和時間漂移，減小壓力傳感器的熱零點漂移的措施是各力敏電阻的電阻值及其溫度系數的相等性。It is a very high advancement to the development from two - pressure arc - quenching chamber and single - pressure arc - quenching chamber to the self - energy arc - quenching chamber now for arc - quenching theory of sf6 cb make use of the arc blocking effect, namely arc - self - energy, to increase sf6 gas pressure in the arc - quenching chamber and get the efficient blasting effect to extinguish the arc when the arc current is zero
Sf _ 6斷路器從雙壓式、單壓式發展到如今的自能式是斷路器滅弧原理的一個重大飛躍。自能式sf _ 6斷路器利用電弧阻塞效應即利用電弧本身的能量使滅弧室內sf _ 6氣體的壓力升高，在電弧過零時產生有效的氣吹而熄滅電弧。Study of the measuring methods of zero - time constant for coil - block in transformers
變壓器繞組電阻零時間常數測量方法的研究Then, based on the estimation algorithm decomposing the measurement of voltage scope and power scope, the problems of the location of transformation tap settings and the tide current estimation of zero - impedance branches in state estimation are solved ; and detection and identification of bad data in state estimation are deduced and stimulated, also a hybrid method of detection and identification is brought forward
隨后，在基於分解電壓測量量和功率測量量的估計演算法的基礎上，對狀態估計中經常出現的變壓器抽頭位置問題和零阻抗支路潮流估計問題進行了分析和處理；對狀態估計的不良數據檢測與識別方法進行了推導和模擬，並提出了一種混合檢測方法。The traditional level measuring methods can n ' t meet our demand because the subjective investigated is in such a poor systemic condition that the temperature is a little high and there ' s so many mill dust and steam there. in this article we perform systemic discuss and research against the dynamic level measuring method under special working condition on the basis of analyzing kinds of level measuring technique in and abroad. first we establish the pressure distribution mathematic model in storage bin and then deduce the mathematic relation between level height and the uniform stress on the bottom of the bin and designed a resistance compressive stress sensor used for the special condition and put forward a resoivement according to its zero excursion existing in practical use
由於本研究系統被測對象環境溫度較高且潮濕，同時料倉中有大量粉塵及蒸汽，因此傳統的料位檢測方法不能滿足本測試要求。本文在分析國內外各種物位檢測技術的基礎上，針對特殊工況下動態物料高度的檢測進行了系統的探討與研究。首先建立了料倉中的壓力分佈數學模型，推導出料位高度與倉底均布壓力間的數學關系式，並據此設計了中溫電阻應變式壓力傳感器，同時對它在實際應用中存在的零點漂移等問題提出了改進措施，提高了傳感器性能，解決了上述特殊工況下動態物料檢測的技術難題。Leading edge cuts the front from the the main - voltage sinus after the zero - cross
飛機螺旋槳的前邊緣在零交叉只后阻斷了高電壓的前峰。According to zero sequence voltage distribution from system zero sequence impedance to shunt reactor zero sequence in zero sequence circuit, the zero sequence voltage at the terminal of shunt reactor and the zero sequence compensating voltage at neutral are compared in the scheme
即根據零序網路中零序電壓在系統零序阻抗和電抗器零序阻抗上的分佈情況，通過直接比較電抗器首端零序電壓與補償到電抗器末端中性點的零序補償電壓的幅值大小，來判別電抗器匝間故障。Zero voltage resistance
零壓電阻Insulation resistance and withstand voltage testing methods of parts for railway signaling
鐵路信號零件的絕緣電阻及耐電壓試驗方法The second, the realization of the zvs has no concerned with the attribute of load. with the load of light or full, even the resistance or inductor load, the chopper can ensure that the main - switches will realize the zvs switching
其次，實現零電壓軟開關的條件與負載的性質和程度沒有關系，無論是電阻性負載還是大電感負載，無論是輕載還是滿載，都可以實現功率器件的零電壓開通和關斷。分享友人