電場中燒結 的英文怎麼說
中文拼音 [diànchǎngzhōngshāojiē]
電場中燒結
英文
sintering in electric field-
In chapter two, we fabricated r - ni - fe / al2o3 nanocomposites successfully by using ball - milling mixing method plus hot - pressing process. meanwhile, their microstructures are characterized by x - ray diffraction ( xrd ) analyser, transmission electron microscopy ( tem ), field emission scanning electron microscopy ( fe - sem ) and brunauer - emmett - teller ( bet ). the results indicate that ni - fe particles are homogenously dispersed in the matrix in the composites
在第二章中，我們採用高能球磨混合方法加上熱壓燒結工藝，成功制備了ni - 20fe al _ 2o _ 3納米復合材料，並通過x射線衍射儀（ xrd ） 、透射電鏡（ tem ） 、場發射掃描電鏡（ fe - sem ） 、比表面孔隙儀（ bet ）對該復合材料的微結構進行了表徵。The temperature distribution on the high temperature side of an electric tunnel furnace is analysed and simulated on the basis of the principle of thermal radiation by the way of thb ( thermal heat balance ). the heated silicon carbon sticks are decomposed into innumerable tiny heating faces, which exchange the heat with the heated materials. a numerical model based on the radiation intensity law is constructed to calculate the energy absorbed by the heated materials and simulated by a computer. the results showed that the even distribution of temperature can be obtained by optimizing the arrangement of the silicon carbon sticks according to the calculation results to make the structure design more reasonable. these calculation results have been used in the practical designs and the expected objectives achieved
利用熱輻射原理，採用熱平衡法對電熱隧道窯的高溫恆溫區溫場進行了分析和模擬.計算中將發熱棒分解為無數微元發熱面與燒結體進行熱交換，依據輻射強度定律，建立了燒結體接收能量的數學模型，並用計算機進行了模擬計算.結果表明，依據模擬結果來優化硅碳棒的排布，可使結構設計更加合理，進而可以獲得分佈均勻的恆溫區溫場.計算結果已在窯爐設計中應用，實踐效果良好And is it the same as under radiation heating ? do the special electric and magnetic fields produced by bpec accelerate atom diffusion ? understanding the above questions fully is a key to expose the mechanism of pecht
在脈沖大電流加工過程中原子是如何擴散的，與一般的加熱燒結、焊接是否一樣，脈沖大電流形成的特殊電場及磁場是否對原子的擴散有大的推動作用，弄清這些問題成為進一步揭示脈沖大電流熱加工機理的關鍵。In this paper, three unique models were designed to research atom diffusion at interface, contacting line and joining point under bpec heating and compare with it under radiation heating in order to find out if bpec speed atom diffusion. the first model was aimed to research atom diffusion at interface under bpec heating. experiment condition of bpec diffusion welding sheet cu and ni : direct diffusion welding, at a pressure of l0mpa, welded at 750 ~ 900, with heat rate of 200 ~ 400 / min for 10mm, on / off of 6 / l ~ 48 / 8, with die or not, vacuum of 6pa
本文設計出三種樣品預構件，研究脈沖大電流加熱條件下片狀材料、線狀材料和球形顆粒之間的原子擴散過程，弄清脈沖大電流加熱條件下原子擴散與一般燒結和焊接過程中原子擴散的區別，以證實特殊的電場和磁場是否對原子的擴散有推動作用，揭示脈沖大電流加熱條件下原子的擴散過程，探索脈沖大電流熱加工技術快速高效的原因。The x - ray diffraction, scanning electronic microscope and the squid were used to characterize the properties of the mgb2 core in mgb2 / fe tapes and wires. the effect of the proportion of mg, b and sic as well as the sintering parameters on the phase formation, microstructure and the critical current densities of mgb2 / fe tapes and wires was discussed in details. the results showed that the high purity of mgb2 core could be synthesized by both the traditional vacuum sintering and the sparking plasma sintering and the vacuum sintering environment restrained the oxidation of mg effectively
相對于傳統真空燒結， sps燒結方式成相速度快、樣品晶粒細小均勻、 mgb2超導芯緻密性好、晶間連接優良，因而sps燒結樣品的臨界電流密度明顯高於傳統真空燒結樣品，其中未摻雜的帶材樣品經過sps800 ， 15分鐘燒結后，自場下的臨界電流密度jc值在10k時達到8 . 64 105a / cm2 ，而且隨著測量溫度和外加磁場的增加， sps燒結樣品的臨界電流密度下降率比傳統真空燒結樣品緩慢，在20k ，自場時為5 . 97 105a / cm2 ， 20k ， 3t時，臨界電流密度值仍大於104a / cm2 。In experiment both different aluminum were screen printed on the silicon and then sintered in the same conditions, the results show the open voltage and the iqe of long - wave with the uniformity junction solar cell is higher than the junction non - uniformity one ， which provided a good technical guiding for the industry
實驗上對兩種不同鋁漿在相同的條件下進行燒結產生的鋁背場的情況作了比較，得出燒結平整性較好，顆粒較小與矽片接觸較好以及不含其它雜質復合中心的鋁背場，其電池的開路電壓和長波光譜響應要好。分享友人