電焊調節器 的英文怎麼說

中文拼音 [diànhàndiàojiéqì]
電焊調節器 英文
welding regulator
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 調節器 : regulator; adjuster; governor; controller; conditioner; actuator; phaser
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  1. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  2. Welding personnel. approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials

    焊接操作人員.金屬材料全機械化和自動焊接用熔焊和電阻焊調節器的焊接操作人員的合格考核
  3. Aiming at the problems of the k190jik rail welding machine, that the parameter modification is difficult, the welding process is not enough stability and the welding machine has no on - line diagnosis function, in this paper, the control system of the welding machine was promoted completely adopting the fx2n - 64mr programmable logic controller and the pcl - 1800 data acquisition card, the das ( data acquisition system ) was set up by using labview and visual basic software, the functions of welding voltage stabilizing and adjusting, current controlling and intellectual modification was improved, welding quality diagnosis system was built up, and the assembling and debugging of the control system was completed, including the process experiments

    本文針對k190jik鋼軌焊機控制系統存在參數修改困難、焊接過程不夠穩定、無焊接質量在線診斷功能等問題，採用日本三菱公司fx2n - 64mr可編程序控制器、研華工控pcl ? 1800數據採集卡等為核心控制部件，對焊機的整機控制系統進行了全面升級。運用軟體labview和vb開發了數據採集系統，完善了焊接穩壓、調壓、電流恆值控制與智能調節功能，利用vb建立了焊接質量在線診斷系統，並完成了系統組裝調試與工藝試驗研究工作。
  4. Abstract : the multifunctional inverter power sourcethe handy inverter welding, plating & charging manchine, developed with advanced inverter and micro - electronics control techniques, adopts “ half - bridge power expansion supply midpoint voltage autocontrol setting ”, and technically and effectively having solved inverter subvision of inverter power expansion circuit for leaning magnetism, reliability of high - power inverter setting, achives combination of constantcurrent and constantvoltage export, and realizes low - voltage dc and high - voltage ac double power supply

    文摘:運用先進的高頻逆變技術和微電子控制技術設計研製的逆變式多功能電源便攜式逆變焊鍍充電多用機，採用「半橋式功放級供電中點電壓自動控制調節裝置」 ，在技術上解決了逆變功放電路因偏磁而造成的逆變顛覆，有效地解決了大功率逆變器的可靠性問題；進行多種外特性的綜合設定，實現了恆流與恆壓輸出的合一；與傳統焊機相比，實現了開環和閉環狀態下都互不影響的低壓直流電瓶和高壓交流雙供電
分享友人
分享到 Line

分享到臉書