電離聚合 的英文怎麼說

中文拼音 [diànlíjùgě]
電離聚合 英文
ionization polymerization
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 聚 : 動詞（聚集; 聚積） assemble; gather; get together
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 聚合 : 1 （聚集到一起） get together2 [化學] （單體結合成高分子化合物） polymerization; polymerize 3 [生...
  1. In this thesis, a kind of reversible immobilization method based on the plasma - polymerized film ( ppf ) used for effective immobilization of active bio - molecules and easy reproduction of sensors is developed. the surface of quartz crystal microbalance ( qcm ) is firstly prepared with plasma - polymerized film of butyl amine by glow - charge technique and then covered with a negative - charged polyelectrolyte by self - assembling. through strong electrostatic attraction, antibodies ( antigens ) positive - charged are immobilized for the determination of antigens ( antibodies )

    本論文基於等離子體聚合膜，設計了一種既能固定生物活性物質又易於傳感器再生的可逆固定化方法，即採用輝光放電的等離子體沉積技術，先在石英晶體上沉積一層正丁胺等離子體聚合膜，再在膜上自組裝一層帶負電的聚電解質，用以靜電吸附固定抗體（抗原）測定抗原（抗體） 。
  2. A series of near roundness cds nanoparticles with a particle diameter of 3 ~ 6nm have been prepared by controlling the concentration and proportion of reactants and adopting sodium hexametaphosphate as stabilizing agent. the studies demonstrate that these particles present obvious quantum size effect and an appropriate excess of cd2 + ion and hexametaphosphoric acid group polysnion are helpful to the dispersion and flame capability ' s improvement of particles. another series of near roundness monodisperse au nanoparticles with a diameter of 12. 3nm was prepared via sodium citric acid deoxidizing auric chloride acid

    利用六偏磷酸鈉作為穩定劑，通過控制反應物的濃度及比例，制備了粒徑為3 6nm 、呈近似球形的cds納米顆粒，光譜測試結果表明，顆粒具有明顯的量子尺寸效應，適當過量的cd ~ （ 2 + ）離子以及六偏磷酸根聚陰離子有助於顆粒的分散並提高其發光性能；採用檸檬酸鈉還原氯金酸，制備了接近球形、平均粒徑約為12 . 3nm的單分散體系au納米顆粒；採用wessling的前驅聚合物法獲得導電聚合物ppv前驅體。
  3. In this article, the bellcore method was used to prepare polymer electrolyte membrane based on pvdf - hfp, and polymer electrolyte membranes under different conditions were prepared by changing sorts of solvents 、 ratio of dbp and solvent. effects of ratio of plasticizer and solvent on the liquid uptake 、 sem 、 mechanism capability 、 ionic conductivity 、 electrochemical stability window of polymer electrolyte membrane were also studied. through optimizing the preparation technics, the integrated effects of additives such as pc 、 ec 、 dbp and nanophase al2o3 on the ionic conductivity 、 liquid uptake were studied

    本文以聚偏氟乙烯-六氟丙烯共聚物pvdf - hfp為基質，採用bellcore制膜法制備了pvdf - hfp聚合物電解質膜，通過改變增塑劑dbp的含量、溶劑的種類及溶劑的含量制備了不同條件下的聚合物電解質膜，分別研究了增塑劑含量、溶劑含量等對聚合物電解質膜的吸液率、表面形貌、機械性能、離子電導率、電化學穩定窗口等的影響;對制備工藝進行了優化，研究了各種添加劑如pc 、 ec 、 dbp及納米al2o3對聚合物電解質膜的離子電導率、吸液率等性能的綜合影響。
  4. The electrical conductance of the gold / polymer composite films was tunable, and a low resistivity of the order of 10 ~ ( - 4 ) cm was yield. the conducting mechanism was not determined, perhaps the tunnel effect and the foreign - substance - electron - transfer should be considered

    聚合物金納米粒子復合薄膜的電阻率可調，電阻率最低可達10 ~ （ - 4 ） ? cm量級，導電機制可能與隧道效應及雜質離子導電有關。
  5. The pyrogallol was adhered on the surface of the solid electrode by the direct oxidative electropolymerization to construct the chemical sensors for bi ( iii ). the sensor exhibits perfect long stability and reproducibility. a low detection was obtained in the determination of bi ( iii ) and this way can be applied to determine the real samples such as human hair and nails

    2 、將修飾劑鄰苯三酚直接電聚合到固體電極的表面，研製bi （ ）離子化學傳感器，該修飾電極穩定性和重現性很好，克服了以往碳糊電極機械強度差、重現性不好的缺陷，測定bi （ ）達到了很低的檢出限，應用於人發和指甲等實際樣品的測定。
  6. Gel polymer lithium batteries ( gplb ) not only have the excellent performance of liquid lithium battery, but also can resolve the possible problems of leakage and blast owing to no free liquid electrolyte in gplb. it is also very convenient to design the shape at will

    凝膠聚合物鋰離子電池不僅具有液態鋰離子電池的優良性能，而且由於電池中不存在游離的電解液，不但改善了液態鋰離子電池可能出現的漏液、爆炸等問題，外形設計也更加靈活方便。
  7. Synthesis and electrospinning of poly ethylene covinyl alcohol end - capped with potassium sulfonate ionomer

    離子聚合物的合成及其高壓靜電紡絲
  8. Firstly, a situ - polymerization method as the preparation process of gplb is introduced and pmma as the polymer matrix of the gel electrolyte is selected. the thermal polymerization process of the gel electrolyte is also optimized

    首先，採用了現場聚合法制備凝膠聚合物鋰離子電池的工藝，根據該制備工藝選擇pmma基作為該凝膠聚合物電解質的聚合物體系，然後對凝膠的熱聚合工藝進行了優化，確定了最佳的熱聚合工藝。
  9. Focusing on the preparation process of lithium battery, thermal polymerization process of the gpe and optimizing the component of the gel electrolyte, the paper intends to resolve some of the key problems mentioned above and to prepare a gplb with good performance

    本論文正是從目前凝膠聚合物鋰離子電池存在的這些問題出發，從鋰離子電池的制備工藝和凝膠的熱聚合工藝研究著手，對gpe的組份進行了改進和優化，制備了性能良好的凝膠聚合物鋰離子電池。
  10. From sem of the polymer, we can found that, the polymer containing no dbp made by solvent of nmp had more and large pores than solvent of dmac, so it had larger liquid uptake and higher ionic conductivity

    從sem測試圖上也可以看出，不含dbp時，溶劑為nmp條件下制備的聚合物膜孔徑比溶劑為dmac時大，孔隙多，吸液率大，離子電導率高。
  11. Recent advances of all - solid - state polymer electrolyte systems that can be probably used in lithium ion batteries are reviewed, focusing on their electrochemical performances, especially the ionic conductivity at room temperature

    綜述了鋰離子電池聚合物常溫固體電解質的最新研究進展。主要關注的是電化學性能，尤其是室溫下的離子電導率。對性能較好的聚合物固體電解質體系進行了概述。
  12. Solvents of dmac and nmp were used to prepare polymer electrolyte membrane, when the ratio of dbp and solvent was 20 %, both of the ionic conductivity can arrive at 10 - 3 s ? cm - 1, and the ionic conductivity of polymer made by nmp was 35 % higher than by dmac

    分別用溶劑dmac及nmp制備了聚合物電解質膜，在增塑劑與溶劑體積比為20 %時，聚合物膜的離子電導率均能達到10 - 3s ? cm - 1 ，且以nmp為溶劑的聚合物膜的電導率比以dmac為溶劑的電導率高出大約35 % 。
  13. In the mean time, i test the separator ’ s performance, including the rate of hole 、 the performance of absorbing electrolyte and the conductance eletrochemical steady range 、 machine intensity test, and then make bettery to test its cycle performance. the test result show that, the spreading separator get better performance, when dbp ’ s percentum reach 50 %, and dry temperature reach 90, after ultraviolet radiation disposal. the test show that, the separator has high conductance reach 6. 1 10 - 3s / cm ( 25 ), and the machine intensity can reach 3. 92 mpa, this separator can meet the need of making bettery, the bettery capability will go down after 30 cycle. and the bettery show worse performance under high temperature, under 70, the bettery will get fire. making the intensified seprator, i find that when dbp % : pvdf % = 40 % : 60 %, dbp % + pvdf % : sio2 % = 70 % : 30 %, the separator get

    但用其制備的電池循環30周期后容量發生衰減，並且電池高溫性能差， 70下電池燃燒;強化聚合物膜的最佳制備配比條件為: dbp : pvdf為40mass % : 60mass % ， dbp含量與pvdf含量之和與納米sio2含量比值為70mass % : 30mass % ;強化電解質隔膜的室溫離子電導率也可達4 10 - 3s / cm左右，完全能滿足聚合物鋰離子電池的使用需要;機械強度遠遠大於流延法制得的隔膜，達到108 . 84mpa 。
  14. The liquid uptake of polymer electrolyte membrane first increase, then remaining the same as the increasing of ratio of solvents. mechanism capability and ionic conductivity fist increase then decrease during the process, but it changed not much in total. through the test of sem it can be found that the structure of membrane changed little during the process

    在增塑劑含量及聚合物基質含量一定的條件下，隨溶劑含量的增大，聚合物膜的吸液率先增大后基本保持不變，機械強度及離子電導率則先增大后減小，通過sem測試可知，膜的表面形貌無明顯變化。
  15. Now the ion conductivity of gel polymer electrolyte ( gpe ) can reach the magnitude of 10 - 3s / cm, which can satisfy the practical request. however, it is still lower than that of liquid electrolyte ( 10 - 2 s / cm ), which causes the fall of high rate discharge and low temperature performance of lithium battery

    目前凝膠聚合物電解質（ gpe ）的室溫離子電導率可達10 ~ （ - 3 ） s cm數量級，已經能基本滿足應用的要求，但相比液態電解液的電導率（ 10 ~ （ - 2 ） s cm ） ， gpe的電導率仍然偏低，使得凝膠聚合物鋰離子電池的高充放電速率和低溫性能都大大的降低。
  16. The progress in stabilizations and stabilization mechanisms of the metal nanoparticles by nonionic polymers, polyelectrolytes, amphiphilic polymers, double - hydrophilic polymers, and dendrimers is reviewed

    本文綜述了非離子聚合物、聚電解質、兩親聚合物、雙親水聚合物、樹狀聚合物對金屬納米粒子的穩定作用及其穩定機理的研究進展。
  17. Exposure of polymeric materials to ionizing radiation

    聚合材料電離輻射的輻照量
  18. For this purpose, 2, 5 - diaminobenzene sulphonic acid ( dabsa ) [ c6h3 ( nh2 ) 2so3h ] can be selected as one monomer of ip reaction. the other monomer can be trimesoyl chloride ( tmc ) [ c6h3 ( coc1 ) 3 ]. in order to introduce the cationic group into membrane, 4 - ( chloromethyl ) benzoyl chloride ( cmbc ) [ ch2c1c6h4 ( coc1 ) ] could be added into organic phase ( tmc ) and used for chemical modification after ip process based on the reaction between 4 - ( chloromethyl ) benzoyl chloride and trimethylamine ( tma )

    為了引入陽離子交換基團，本文採用2 ， 5 -二胺基苯磺酸作為界面聚合的無機相單體；為了引入陰離子交換基團，在均苯三甲酰氯有機相單體中加入一定量的4 -氯甲基苯酰氯，並考慮在無機相中加入適量的聚乙烯亞胺（ pei ）以增加其正荷電性。
  19. The pcr products were electrophoresed on 3 % agarose gel and visualized under uv light

    聚合酶鏈鎖反應的產物以3 %瓊脂電泳分離並在紫外光下觀察結果。
  20. A gel - typed polymer electrolyte based on pvdf - hfp was studied

    本文研究了pvdf - hfp基鋰離子電池聚合物凝膠電解質的性質。
分享友人
分享到 Line

分享到臉書