霧化粉粒 的英文怎麼說
中文拼音 [wùhuàfěnlì]
霧化粉粒
英文
atomized particle-
With gelatin liquor as adhesive and wheat meal as granulation material, the effects on spray granule ' s strength of fluidizing gas velocity, bed temperature, nozzle air pressure and adhesive concentration were studied experimentally in a batch conical fluidized bed spray particle generator
本文在一間歇錐形流化床噴霧造粒器中，以食用小麥澱粉為原料，以明膠的水溶液為粘結劑，實驗研究了流化氣速、床層溫度、噴嘴霧化空氣壓力、粘結劑濃度對噴霧造粒顆粒強度的影響。Exhaust carrying sulfur oxides and powders enter the venturi scrubber to interact with the recovery solvent. when passing through the neck, the section surface constricts and the
含硫氧化物及粉塵廢氣自頂部進入文氏洗滌塔和洗滌液接觸流經喉部，由於截面積縮小，高速氣體將洗滌液噴成霧狀，而達到慣性沖擊去除粒狀物的目的。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。The feasibility of copper matrix reinforced by cr2o3 particles was discussed from the aspect of the demand of composite on reinforcer, interface and its formation. crcu alloy powders prepared by water atomization were turned into cr2o3 / cu compound powders, which were made into composites
本文從復合材料對顆粒增強相的要求、復合材料的界面以及復合材料的成型等角度分析了cr _ 2o _ 3顆粒作為彌散強化相增強銅基體的可行性，採用水霧化法制備crcu合金粉末，並通過預氧化的方法得到cr _ 2o _ 3 cu復合粉末，運用粉末冶金法制備cr _ 2o _ 3 cu復合材料。分享友人