頂部承載鋼 的英文怎麼說
中文拼音 [dǐngbùchéngzǎigāng]
頂部承載鋼
英文
upper carrier- 頂 : i 名詞（人體或物體的最上部） crown; peak; top Ⅱ動詞1 （用頭支承） carry on the head 2 （從下面拱...
- 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
- 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
- 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
- 鋼 : 鋼名詞（鐵和碳的合金） steel
- 頂部 : top; upper apex; top half; headpiece; roof; ridge; meplat （彈丸的）
-
On the basis of simplified calculation model presented by doctor wangxiaoping, some finite element models are set up. by finite element model program sap93, an analysis of static models of 18m - span and 30m - span w666 acmr in different supporting conditions is made. also a study on the relation between definite support displacement, which reflect variational stiffness of substructure represented by steel column or reinforced concrete column, and load - carrying capacity mechanical performance is made too
本文以w666金屬拱型波紋屋頂為研究對象，沿用王小平博士的簡化計算模型，對18m 、 30m跨波紋拱兩端不同支座形式（鉸支、固支和彈性支座）分別利用有限元計算程序sap93進行計算分析，研究波紋拱在不同跨度，不同支座形式下，不同外荷載作用時對該結構受力性能及穩定承載力的影響，同時分析下部支承鋼柱、鋼筋混凝土柱的剛度變化體現為允許支座位移的大小與結構受力性能及穩定承載力之間的關系。Abstract : based on the systematic analysis of the shear behavior for r. c. beams, the tests of 11 simple supported beams under the top concentrated loads and the uniform loads are supplemented. the prime variable is shear span ratio, span depth ratio, horizontal web reinforcement ratio and vertical web reinforcement ratio. according to the test results, the working behavior, the prime shear failure modes, the effect of concrete and web reinforcement ( horizontal web reinforcement and vertical web reinforcement ) and other aspects of r. c. beams are analysed. the uniform calculation method for shear capacity of deep beams, short beams and shallow beams for practical is presented
文摘:在對國內外鋼筋混凝土梁的受剪性能進行較系統分析的基礎上，補充了11根鋼筋混凝土簡支短梁在頂部集中荷載和均布荷載作用下的試驗，試驗梁的主要變化參數為剪跨比、跨高比、水平腹筋率和垂直腹筋率.根據試驗結果，對試驗梁的工作性能、主要的剪切破壞形態、混凝土項的抗剪作用、抗剪腹筋（包括水平腹筋、垂直腹筋）的作用等進行了較為深入的分析，提出了可適用鋼筋混凝土深梁、短梁和淺梁相互協調的受剪承載力的統一計算方法On the basis of detailed comparison and analysis, the paper proposed ways of using the k2 bogie and hdsa light - duty solid wheel, getting through the partition wall, canceling the longitudinal sill of the roof and decreasing the thickness of the board where the value of stress is low, using high intensity steel, increasing section dimensions of center sill and side sill, to improve the whole carrying capacity
本文在比較分析的基礎上，提出了裝轉k2轉向架，採用hdsa輕型碾鋼輪，打通隔墻，取消車頂縱向梁，在應力小的部位減薄壁厚的減重對策；採用高強度耐候鋼，加大中梁、側梁的截面尺寸等措施，提高車輛的承載能力。
分享友人