預拉伸過程 的英文怎麼說

中文拼音 [yùlāshēnguòchéng]
預拉伸過程 英文
pre-drawing process
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 拉 : 拉構詞成分。
  • 伸 : Ⅰ動詞（展開） stretch; extend Ⅱ名詞（姓氏） a surname
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 過程 : process; procedure; transversion; plication; course
  1. ( 2 ) another interesting phenomenon is founded that the center of south asia high in the upper level of troposphere is stabile and nearly motionless during the processes of the westward extension of western pacific subtropical high, but its eastern ridge strengthens and extends eastward remarkably because of the anticyclone moves westward over the southeast japan, which may lead to the westward extension of subtropical high in the middle level of troposphere. ( 3 ) in the low level of troposphere, the north australia cold air activity plays an important role on the westward extension of subtropical high

    （ 2 ）本文在研究副高西伸過程中指出，高層200hpa上日本東南部的高壓併入南亞高壓，導致南亞高壓脊的增強發展，對低層500hpa上副高的加強、西伸可能起到引導的作用；同時，對流層低層850hpa上孟加拉灣槽在副高西伸過程中加深，並在西伸脊點到達最西點的前4天強度達到最強，這為預報西太平洋副高的活動提供了參考。
  2. 2. the residual stresses in pre - stretched aluminum alloy plates are successfully measured and analyzed. the measurement precision and applicability of the modified layer removal method are analyzed and evaluated by experiments

    2 、鋁合金預拉伸板內部殘余應力分佈規律的研究通過試驗研究對改進剝層法測試理論的測試精度及工程實用性進行了分析和評估。
  3. Machining deformation of aircraft monolithic component is simulated by finite element method ( fem ) and validated by experiment. the initial residual stress in pre - stretched plate is generated by simulating quenching and stretching processes. with a single tool - tooth milling process fem, the machining loads in monolithic component material removing is obtained. restart - calculation is put forward to complete the whole simulation of machining process. to verify the fem result, an experiment is carried out. the deformation distribution of the monolithic component resulting from fem shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. lengthy and expensive trial and error experiment process can be avoided

    在模擬淬火、拉伸過程獲得含有初始殘余應力的預拉伸板材以及模擬單齒切削過程獲得切削載荷的基礎上，提出並採用接力演算法，對一航空整體結構件的材料銑削過程進行有限元模擬，同時進行了試驗研究.結果表明，有限元模擬的整體結構件的變形與試驗具有一致性，從而證明提出的整體結構件加工模擬關鍵技術的可行性，避免了為研究加工變形而進行的繁瑣的試錯法
  4. Abstract : the sensation of wearing pressure have assessed for knit garments having different sizes and fabrics having the different extensibility, by developing a wearing experimental procedure. at the same time, the objective clothing pressure, the fabric ' s extensibility and the garment ' s fitness have measured. regression analysis showed that the garment ' s fitnessand fabric ' s extensibility had great predictive power for the subjective pressure assessment

    文摘:設計了一組服裝用於穿著實驗.對不同尺寸、不同彈性性能的緊身長褲進行了主觀壓力感評價，並測量了服裝壓、衣料的拉伸變形程度和服裝寬裕率.通過分析，選用服裝寬裕率和織物的彈性模量作為指標預測服裝的穿著壓力感
  5. In our experimentation, we combine fiber bragg grating with tb - dy - fe single crystal, we can measure the current which produces the magnetic field when we measure the shift of bragg wavelength because of magnetostrictive strain of tb - dy - fe single crystal in magnetic field, we also study the relation between bias field, strain of current sensor

    本實驗將光纖布拉格光柵與tb - dy - fe結合起來，利用tb - dy - fe在磁場下的伸縮引起布拉格波長的改變，來測量產生磁場的待測電流的大小。在實驗中我們還研究了偏場，預應力與傳感器的關系，在這個過程中我們找到了與傳感器有關的最佳設計參數。
  6. Finally, the paper provides the theoretic method suitable for calculating the tensioning elongation of the tendons, and checks the method as well by measurement data from several engineering projects

    同時，分析了預應力束的束效應引起的鋼絞線的重新排列，以及彎曲段等效徑向荷載產生的徑向位移，最後得出了適合小曲率半徑預應力束張拉延伸量計算的理論方法，並通過多個工程實測數據進行校驗。
分享友人
分享到 Line

分享到臉書