預淬火 的英文怎麼說

中文拼音 [yùcuìhuǒ]
預淬火 英文
prequenching
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  1. Precaution of quenching crack of dovetail cutter

    預防鴿尾銑刀淬火裂紋的工藝探索
  2. The prevention of quenching crackles in heat - treating technology

    熱處理工藝中淬火裂紋的預防
  3. Aimed to realize the problem of quenched rail qualification forcast through quantitative analysis of quenched rail surface hardness by eddy current, and combined the eddy current theory with the computer image processing and signal analysis, the hardness testing model is established in this paper

    針對渦流無損檢測淬火鋼軌踏面硬度的定量分析來實現淬火鋼軌質量保證預報問題，將電渦流理論與現代計算機圖象處理和信號分析相結合，完成硬度測試模型建立。
  4. Abstract : aimed to realize the problem of quenched rail qualification forcast through quantitative analysis of quenched rail surface hardness by eddy current, and combined the eddy current theory with the computer image processing and signal analysis, the hardness testing model is established in this paper

    文摘:針對渦流無損檢測淬火鋼軌踏面硬度的定量分析來實現淬火鋼軌質量保證預報問題，將電渦流理論與現代計算機圖象處理和信號分析相結合，完成硬度測試模型建立。
  5. The paper expounds the main reasons of formation of quench distortion and gives some relevant precautions and straightening solutions

    本文較詳細探討影響工件淬火變形的主要因素，提出了相應的預防和矯直措施。
  6. Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth

    第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析，主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。
  7. Machining deformation of aircraft monolithic component is simulated by finite element method ( fem ) and validated by experiment. the initial residual stress in pre - stretched plate is generated by simulating quenching and stretching processes. with a single tool - tooth milling process fem, the machining loads in monolithic component material removing is obtained. restart - calculation is put forward to complete the whole simulation of machining process. to verify the fem result, an experiment is carried out. the deformation distribution of the monolithic component resulting from fem shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. lengthy and expensive trial and error experiment process can be avoided

    在模擬淬火、拉伸過程獲得含有初始殘余應力的預拉伸板材以及模擬單齒切削過程獲得切削載荷的基礎上，提出並採用接力演算法，對一航空整體結構件的材料銑削過程進行有限元模擬，同時進行了試驗研究.結果表明，有限元模擬的整體結構件的變形與試驗具有一致性，從而證明提出的整體結構件加工模擬關鍵技術的可行性，避免了為研究加工變形而進行的繁瑣的試錯法
  8. The lath width of martensite can be fined noticeably by pre - strained quenching at non - dynamic recrystallization to approach nanometer magnitude ( the average width is 120nm )

    採用非動態再結晶溫度下的預應變-淬火，提高馬氏體相變形核率，可以超細化馬氏體的板條晶片寬度，使之接近納米量級水平（平均寬度達到120nm ） 。
  9. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
  10. Steel for the prestressing of concrete - part 3 : quenched and tempered wire

    混凝土預應力鋼筋.第3部分:淬火和回火鋼絲
  11. Many means such as reasonable selecting mould material, correct forging process, appropriate heat treatment, rough machining of type hole before quenching and so on are taken in production to prevent deformation and cracking of mould effectively

    在生產實踐中，通過合理選擇模具材料、正確的鍛造工藝、合適的熱處理工藝以及淬火前形孔預加工等措施，可有效防止模具的變形與開裂。
  12. Determination of shear strength for in - plane forces of joints between prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure ; german version en 1739 : 1998

    結構件平面承載時蒸氣淬火氣孔混凝土預製件或堆放空
分享友人
分享到 Line

分享到臉書