預熱空間 的英文怎麼說
中文拼音 [yùrèkōngjiān]
預熱空間
英文
preheated air-
The afterheat, which is collected by recovery devices, in winter can be used as the low level thermal source of heat pump, and in summer can preheat feed water, thus equivalent an economizer. because energy flows in the system so reasonably that energy is used to the most, therefore, its energy conservation effect is significant, and the operating expenditure declines consequently. the sewage can be reused after due treatment, thua it has a certain social and ecological benefit, too
本研究中選用分離式熱管裝置提供洗浴用水,利用水源熱泵裝置,一機兩用,進行空間供熱和製冷,並通過余熱回收器對系統內的余熱進行回收,冬季可作為水源熱泵的低位熱源,夏季可對鍋爐給水進行預熱,起到「省煤器」的作用。這樣實現系統內的能量合理流動,從而達到節能的目的,同時洗浴污水經適當的處理后可以回用,因而還具有一定的社會和生態效益。Compared with traditional mechanical and optic gyros, hrg has such advantages as no high speed circumvolving or moving parts in structure, no warm - up time and short start - up time, wide signal band in frequency, low excursion noises, great endurance in over loading, nuclear radiation and short time power off, small bulk, light weight, low power cost and long life, which is suitable for space applications
與傳統的機械陀螺和光學陀螺相比,半球諧振陀螺具有如下優勢:結構上無高速轉子、無活動部件;不需預熱,啟動時間短;信號頻帶寬,漂移噪聲低;能承受大的機動過載;抗核輻射,並可經受短時間電源中斷的影響;體積小,重量輕,功耗低,壽命長,非常適合空間應用。Control on intimate terms of the air preheat device
空氣預熱器的間隙控制In this thesis, several advanced control methods are adopted to improve the performance of the traditional air preheater leakage control system using non - touched sensor
本文採用了多種先進控制方法,用來改進傳統的非接觸式空氣預熱器密封間隙控制系統。Based on can bus, this thesis develops an innovational air preheater leakage control system, with pcs structure to fulfil the optimal control over system structure and the multi - signals transfer
為了優化控制系統結構並解決系統中多種信號的傳遞問題,本課題以can總線為基礎,建立了fcs結構的新一代空氣預熱器密封間隙控制系統。Because the system error is ineluctable for mode, it is necessary to correct the simulation fielde effectively. in this paper, based on the idea of combined eof correction, the interannual simulation of sea surface wind stress anomalies of the tropical pacific ocean by lap two - level atmosphereic model have been corrected, result of corrected erperiment shows that the corrected field is more similar to the observation field, especially on the distribution of the space. three prediction experiments also shew that correcting scheme of combined eof can improve the interannual prediction veracity of model
在本文中,基於「聯合自然正交展開誤差訂正」的思想,將中科院大氣物理研究所兩層大氣環流模式輸出的熱帶太平洋海表風應力異常的跨年度模擬場進行訂正,訂正試驗的分析結果表明,訂正後的熱帶太平洋海表風應力距平場與相應觀測場年際變率分量的相似程度遠遠好於模式模擬的結果,尤其是在空間分佈方面的改善非常顯著;三組跨年度訂正檢驗結果也表明,訂正後的跨年度預測結果明顯好於模式的預測結果。Clearance control strategy in rotary air - preheater
回轉式空氣預熱器密封間隙控制策略You should follow the installation instructions for the luminaires, such as installing away from combustible surface ( wall paper, wooden false ceiling ), allowing sufficient room for heat dissipation ( particularly luminaires fitted with tungsten halogen lamps ), ensuring effective earthing connection ( such as adding star and spring washers at the earth terminal ), and adopting proper anchorage to support its weight
燈飾應按照指示安裝,注意要遠離容易燃燒的表面(例如墻紙、木製假天花) ,預留足夠的散熱空間(尤其是裝有鎢絲鹵燈的燈飾) ,確保有效接地(例如在接地終端加上菊花介指和彈弓介指) ,並因應燈飾的重量,選用適當的安裝方法(例如大型的吊燈,須選用拉爆螺絲等) 。Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況,提出了若干技術改造措施包括,增大對流管表面積以增大對流段的熱負荷;增加輻射管的換熱面積;修正煙囪高度;換用新型燃燒器,變自然通風為強制供風,以增大燃燒器的發熱量,減小過剩空氣系數,節省燃料2 % 3 % ;在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度;採用高溫輻射塗料增強輻射換熱效果,從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況,提出了若干技術改造措施包括,增大對流管表面積以增大對流段的熱負荷;增加輻射管的換熱面積;修正煙囪高度;換用新型燃燒器,變自然通風為強制供風,以增大燃燒器的發熱量,減小過剩空氣系數,節省燃料2 % 3 % ;在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度;採用高溫輻射塗料增強輻射換熱效果,從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。Most air space - heating systems also preheat domestic hot water through an air - to - liquid heat exchanger
大部分空氣空間?加熱系統也會通過氣水熱交換器預加熱家庭里的熱水。Taking some tubular air pre - heater used in one boiler whose capacity is 130 t / h as an example, new blue print with inner trachea is completed by means of computer program. several key design variables may be changed, such as diameter of pipe and velocity of flow of gas. these cases have been considered, and their results have also been compared with each other
比較了幾個重要的設計變量,如外管徑、煙氣流速等參數變化時,總傳熱系數和空預器本體管子總重量,阻力損失以及最低管壁溫度等幾個重要設計結果的變化趨勢,對內螺紋管空氣預熱器的設計具有借鑒意義;其間還分析了內螺紋管與光管在設計時的不同之處;最後,初步分析了內螺紋管的優化設計問題,提出了一些建議。8. 1 - octadecanol also affects slightly the heat of micropcm phase transition, but it easily induces microcapsules with mf resin as the shell to occur conglomeration. for the microcapsules with about 9 % 1 - octadecanol in the core, their super - cooling can al
11 、加有環己烷的相變材料膠囊可以進行高溫熱處理,熱處理溫度應控制在160 ~ 180之間,熱處理時間為30 ~ 60min為宜,此時,膠囊產生預留膨脹空間,囊壁發生交聯。The prediction of disastrous space weather is a hot topi c among solar - terrestrial physics and high technological fields. we propose that the future forecasting of the physical conditions that the violent solar disturb ance causes at the earth by propagating in solar wind depends heavily on the num erical method. this paper analyses the existing problems we are facing in the num erical prediction of disastrous disturbance events in solar - terrestrial space, an d then gives some suggestions for future study. for such a purpose, a six step sol ution method is developed to deal with one - dimensional symmetric interplanetary shock dynamics. it should be point out that that initialization of fully self - con sistent 3 - d mhd codes considering the solar - interplanetary - geomagnetic coupled r elations with initial - boundary values at 1r of the global output of solar pl asma and magnetic field using available solar observations is an essential requi rement in space weather operational codes for forecasting purposes
空間災害性天氣的預報是日地物理學界及高科技領域的熱門話題.未來預測太陽劇烈擾動所造成的行星際風暴到達地球空間的狀態勢必藉助于數值方法.淺析了空間災害性擾動事件數值預報存在的問題及未來設想,針對這一目的對一維球對稱問題提出了處理行星際激波的6步求解方法,指出未來空間災害性擾動事件預報模式應是一個基於三維的以真實太陽風為背景自洽建立起來的、以太陽等離子體輸出及磁場全球結構為初邊值、太陽、行星際、地磁因果耦合模式The results show that in the later stage of the nucleation process, the maximum slip velocity is monotonically accelerating ; the slipping hot spot ( where the slip rate is maximum ) migrates spontaneously from a certain instant, and such migration is spatially continuous ; when the maximum velocity reaches a detectable order of magnitude ( at least one order of magnitude greater than the loading rate ), the remaining time is 20 hours or more, and the temporal variation of slip velocity beyond this point may be used as a precursory indicator ; the average slip velocity is related to the remaining time by a log - log linear relation, which means that a similar relation between rate of microseismicity and remaining time may also exist ; when normal stress variation is taken into account, time scale of such processes can be extended by about 2 times
結果表明,在成核的後期階段:最大位移速率單調加速增加;滑動熱點(最大滑動速率處)在後期階段開始自發性遷移,且在空間上連續;當最大滑動速率達到可以明顯探測的量級時(高於載入速率一個數量級以上) ,倒計時間為20小時或更長一些,這時的速率變化可作為臨震預測標志;平均滑動速率與倒計時間的關系在臨震階段呈對數線性趨勢,由此可推測微震活動增長率與倒計時間同樣存在對數線性關系;正應力的變化對上述時間尺度有延長作用,使之大致增加到原數值的2倍。New idea toward the calculation methods for the rotary air preheater rotator mushroom type deformation and the installation method of folding gaskets. were put forward the calculation method for the pre - arangement of the folding line gap was presented
摘要對回轉式空氣預熱器轉子蘑菇狀變形量的計算方法和密封片的安裝方法提出了新的觀點,並對這折線密封間隙的預留提出了新的計算方法。Computer hackers will open a new front in the multi - billion pound " cyberwar " in 2007, targeting mobile phones, instant messaging and community web sites such as myspace, security experts predict
安全專家預測: 2007年,電腦黑客們將在火熱的「戰爭」上開拓一片新戰場,襲擊目標為、即時消息和社區網路,例如共享空間。Computer hackers will open a new front in the multi - billion dollar cyberwar in 2007, targeting mobile phones, instant messaging and community web sites such as myspace, security experts predict
安全專家預測: 2007年,電腦黑客們將在火熱的「網路戰爭」上開拓一片新戰場,襲擊目標為手機、即時消息和社區網路,例如共享空間。While the market awaits with keen interest the inevitable pause in the upward trend of interest rates in the us, it also expects considerable head room for interest rates in europe and japan
市場一方面熱切期待著美國加息周期無可避免的暫停,同時又預期歐洲及日本利率會有頗大的上調空間。System structure : “ shuangdeng ” gfm vrla battery can be installed by cabinet, shelf, and ground arrangement, thermal dissipation space has been laid out to effectively avoid thermal runaway
系統結構: 「雙登」 gfm型閥控密封鉛酸蓄電池既可採用櫃、架安裝,也可地面排放,單體間預留了散熱空間,能夠有效防止電池熱失控。分享友人