顆粒間孔率 的英文怎麼說
中文拼音 [kēlìjiānkǒnglǜ]
顆粒間孔率
英文
interparticle porosity-
The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites
研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。Pore parameters ( porosity and distribution of pore diameter ) of porous glass prepared by filler principle were measured and analyzed. they were mainly determined by the volume ratio and the particle diameter of the pore former in the green body. preparation and sintering process of the samples resulted in the difference between the porosity and the volume ratio of the pore former. they were also responsible for the deviation between the distribution of poer diameter and the particle diameter of pore former
研究表明，利用填充法制備的多孔玻璃的孔參數（氣孔率、孔徑分佈）可進行設計與控制，多孔玻璃的氣孔率和孔徑分佈主要取決于成孔劑的體積比及其顆粒分佈，前者與後者之間的偏差取決于生坯制備及燒結過程。The particles aggregation was simulated using particle - cluster and cluster - cluster aggregation model. several type of floes was reached and its morphological characteristics was analyzed the fractal dimension, density and porosity of floes was studied by changing sticking probabilities, sticking position, particle number, particle concentration, difrusion coefficient and motion trajectory. the parameters by which special floes growth were determined. in the study of morphology, floes of yellow river ' s loess particles was observed by tv - microscope. its morphological characteristics were obtained by image analysis. the effect of fractal dimensions by stirring time strring speed, macromolecule flocculant dosage, flocculant concentration and particle concentration was studie. its rule of change was obtained. on the basis of other studies, the flocculation kinetics and floes structure was studied
本文應用計算機模擬技術，在二維空間內採用單體凝聚和集團? ?集團凝聚兩種模型對顆粒凝聚過程進行了模擬，得到了多種形態的絮體，並對絮體進行了形態分析，通過改變粘附概率、粘附位置、顆粒數量、顆粒濃度、擴散系數和運動路徑等模擬參數，我們考察了絮體分形維數、密度和孔隙率隨模擬條件變化的影響規律，得到了形成特定形態絮體的控制參數。Beginning with the analysis of the effects, which are brought by the application of only one kind of pore - former and some other operating factors ( such as sintering temperature, warmth retaining time and so on ), on the properties of the beads, e. g., porosity, strength, size distribution of the beads and pores size, etc., these effects are discussed in detail and the relationship between the factors is studied thoroughly. the use of mpf ( multi - pore - former ) is introduced for the first time, which is of the most importance and significance in this paper
研究從造孔劑選用和燒結過程對顆粒的孔隙率、機械強度、孔徑分佈及粒度分佈的影響入手，找出了造孔劑的種類及含量、燒結溫度以及保溫時間等因素對最終所得產品顆粒的性能影響及它們之間的相互關系，並首次提出將造孔劑復配使用來對填充法加以改進，無需擴孔處理，即能直接制備宏孔徑、高強度、小粒度、比表面大的多孔玻璃載體顆粒。Secondly, the effect of transverse deforming on the property of the wedge pressing was studied. the results showed that : the wedge pressing stock with the transverse deforming amount of 10 % acquired the best performance. the highest density got the biggest rate of slope while with the amount of 30 % the curve was more some special structure and performance as following : the large porosities was crushed into small or linear ones with the high - direction deformation amount of 20 % ; as the increasing of the high - direction deforming, the particles got a further deforming, the porosities got a further crushing, the small porosities were mergered by the large ones and the former then disappeared ; when the amound reached 60 %, the quantity of the porosities would obviously decrease which made the materials compact, the microstructure more uniform and the density and hardness curves more horizontal, the relative desity could reach 99. 7 %, the tensile strength b of the as - compacted samples reached 408mpa with the yield strength s teached 289mpa and the elongation percentage reached 13. 6 %. in addition, the microstructure of the wedge pressing stock under the pressing temperectureof 450 was uniform, the porosities and the boundries of the grains basically disappeared and the conjunction between particles was great
採用雙向楔形壓制，大尺寸噴射沉積5a06鋁合金楔壓坯的組織和性能變化具有如下特點:當高向變形量為20 %時，大的孔洞變形破碎為小的孔洞，或呈線狀孔;隨著高向變形量的增加，顆粒進一步變形，孔洞進一步破碎，大孔「吞併」小孔，小孔塌陷並逐步消失;當高向變形量達到60 %時，孔洞量大為減少，材料基本緻密，組織趨于均勻，楔壓坯料的密度、硬度變化曲線接近水平線，坯料的相對密度達99 . 7 % ，抗拉強度_ b = 408mpa ，屈服強度_ （ 0 . 2 ） = 289mpa ，延伸率= 13 . 6 % ;對比其它的壓制溫度，在450楔形壓制的坯料組織均勻，孔洞及顆粒邊界基本消失，顆粒之間冶金結合良好。The analysis of microstructure of samples showed that the grain of tio2 were very small under 700, the distance of grain became small with temperature increasing, the rate and size of pore was decreasing. the relative density of sample at 900 was 97 % and the grain size of sintered body was about 200nm. when the temperature exceeded 1100, the grain size of body grew up several times ( > 2 m )
Tio _ 2燒結體sem顯微形貌分析表明：低溫（ 700 ）時坯體內顆粒無明顯長大，燒結體緻密度不高（ 80 ）晶粒間距隨溫度升高而變小，氣孔率也隨之降低，氣孔尺寸變小；當溫度超過900時，晶粒間連接緊密，燒結體內出現大量絮狀物質，緻密度大幅度提高，達97以上，小氣孔已聚集成大孔洞且分佈均勻，晶粒長大不明顯（ 200nm左右） ；當溫度超過1100時，燒結體緻密度有所提高，但晶粒尺寸出現異常長大，長大了十幾倍（達2 m以上） 。The results showed that its yield was inversely proportional to the concentration of - amylase and reaction time when the maize starch was hydrolyzed by - amylase ; the granular maize starch was converted into hollow - porous starch by ct - amylase, furthermore it was cracked to the fragments, it was discovered that there were laminated growth ring structure inside starch granular shown on such cracked granular fragments ; the crystallinity of maize starch granule can not he increased by the enzyme hydrolysis ; the thermodynamic stability of the product was reduced when the hydrolysis time was long
檢測結果表明， -澱粉酶催化水解玉米澱粉時，其收率與酶的濃度和反應時間成反比；顆粒狀玉米澱粉發生酶催化水解時， -澱粉酶首先使澱粉形成多孔狀結構，並進一步使顆粒破裂，斷裂的顆粒碎片上顯示出澱粉顆粒內部具有層狀的生長環結構；酶催化水解不能提高玉米澱粉顆粒的結晶度；酶解時間較長時，產品的熱穩定性降低。Results indicate that the samples are comprised of slate - like grains growing up in different directions, and that grain size and pore play a domain role in electrical conductivity and thermal conductivity besides seebeck coefficient
結果顯示燒結樣品由不同取向的片狀顆粒組成，顆粒大小以及顆粒間的氣孔數量對樣品的電導率和熱導率有顯著影響，對seebeck系數影響不大。分享友人