飛行操縱動作 的英文怎麼說

中文拼音 [fēihángcāozōngdòngzuò]
飛行操縱動作 英文
flight function
  • 飛 : Ⅰ動詞1 （鳥、蟲等在空中活動） fly; flit 2 （利用動力機械在空中行動） fly 3 （在空中飄浮遊動） fly...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 操 : Ⅰ動詞1 （抓在手裡; 拿; 掌握） hold; grasp 2 （做; 從事） act; do; operate 3 （用某種語言、方言說...
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 飛行 : flight; flying; aviate; voyage; volitate; hop
  • 操縱 : 1. （控制; 開動） operate; control; roll; steer 2. （支配;控制） rig; manipulate; govern
  1. But the variation of its aerodynamic forces will induce flapping motion and produce the cyclic pitch on the main rotor blades by the bell mixing mechanism. in order to study the effect of bell - hiller stabilizer bar on helicopter stability and control, this paper first analyze the function and the principles, give the flapping equation and a flight dynamic model with bell - hiller stabilizer bar. and then works over the stability and control of uav r - 50 in hover and cruise condition, and analyzed the influence from parameters of the bar to it

    為了深入研究希勒伺服旋翼對直升機穩定性和操縱性的影響，本文首先分析了希勒伺服旋翼的功能和工作原理，推導了伺服旋翼的揮舞運動方程，建立了帶有希勒伺服旋翼直升機的飛行動力學模型，然後以yamahar - 50無人直升機為例，分析該直升機在懸停和前飛時的平衡、穩定性和操縱性，在此基礎上進一步研究希勒伺服旋翼設計參數變化對直升機穩定性和操縱性的影響。
  2. The subsystem is integrated in the cad system of catia, and applies kinematics 3d - manikin and mechanics 3d - manikin in different phase of aircraft cockpit design, and acquires perfect kinematics and mechanics results of pilot. the subsystem whose interface is friendly and utilization is directly, enriches the methods by which the designer estimates an aircraft cockpit design, and enhances the design efficiency and precision

    該子系統集成在catia系統中，在飛機座艙設計的各個階段分別引入了飛行員三維人體幾何模型和運動學模型，通過模擬飛行員的操作動作與計算視角、可達性、操縱力等參數，較好的反映了飛行員的運動學和動力學特徵；界面友好，操作直觀、簡便；豐富了設計人員對飛機座艙設計評估手段，保證了設計效率和精度；有利於飛機座艙設計水平的提高。
  3. The design of aircraft cockpit, which acts as the man - machine interactive interface is of great research value. the author utilizing advanced cad technology, combining the intersecting knowledge with man - machine engineering, robotics, aero - human - engineering, etc, has exploited corresponding modules, such as the simulation of pilot manipulation, vision checkout, vision simulation, accessibility calculation, manipulation force calculation, and established a set of subsystem of aircraft - cockpit - design on the platform of catia

    本文利用先進的計算機輔助設計（ cad ）手段，結合人機工程學、機器人學、航空人體工程學等邊緣交叉學科知識，在catia平臺上，利用其二次開發語言vbscript ，實現了相應的飛行員操縱動作模擬、視界檢查、視覺模擬、可達性計算和操縱力計算等功能，初步建立起一套飛機座艙設計cad子系統。
  4. Thereinto, the controlling method is altered into air cylinder control installed on two sides of transmission shaft, steel structure platform and rushing - board brake. these alterations enable the equipment to be more sensitive and reliable for controlling. steel structure platform makes noise giving off when equipment operates greatly decrease and rushing board brake prolongs the service life of friction belt because it owns large braking area which can contact flywheel and gain large moment and then do little harm to friction belt

    二j53 - 630b型在j53 - 630a型的基礎上作了改進，其中操縱方式改為裝在傳動軸兩端的氣缸操縱，剛結構式平臺，推板式剎車這樣使設備的操縱更靈敏可靠剛結構式平臺使設備工作時噪音大大降低，推板式剎車由於剎車板剎車面積大與飛輪的接觸均勻，所以剎車力矩大同時對摩擦帶的損傷小，延長摩擦帶的使用壽命，推板式剎車平行調整故調整方便。
分享友人
分享到 Line

分享到臉書