驅油過程 的英文怎麼說

中文拼音 [qūyóuguòchéng]
驅油過程 英文
oil displacement process
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 過程 : process; procedure; transversion; plication; course
  1. The initial low ift is very advantageous to enhance oil recoveries, petroleum carboxylat of compound surfactant play the sacrificial agent role in the process of absorption and reduced the sulphonate absorption loss

    復配表面活性劑吸附過程中羧酸鹽起到了犧牲劑作用，降低了磺酸盆的吸附損失，復配體系的這些特點對提高驅油效率很有利。
  2. Through consulting lots of relevant references, present research of direct drive volume control hydraulic servo system is summarized in this paper, the principle and character of this system are expatiated, the principle of vector control is introduced. at the same time, the mathematical model of ac asynchronous motor is set up based on the vector control theory. the mathematical models of both the pump controlled motor and pump controlled cylinder are set up and simulated in this paper

    在查閱大量國內外相關文獻的基礎上，本文綜述了國內外對該系統研究概況，闡述了該類系統原理和特點;闡述了矢量控制的基本原理，並基於這一原理建立交流異步電動機的數學模型;分別建立了泵控馬達系統和泵控缸系統的數學模型，並給出了模擬分析;設計了用於泵控馬達系統的集成閥塊，加工了密閉壓力油罐;針對現有直驅式電液伺服裝置所存在的問題，本文主要針對系統工作過程中所產生的噪音與爬行問題進行了一定的研究。
  3. The paper points out that the reasons for displacement efficiency improving of pressure coring well are as follows : firstly, extra - high injection multiples ; secondly, extra - low critical drive ratio ; thirdly, high velocity fluid ' s big differential pressure drive during the process of coring

    得出導致礦場密閉取心井驅油效率高的原囚：一是特高的注水倍數，二是特低的臨界驅動比，三是取心過程中高黏度流體的大壓差驅動。
  4. In order to solve this contradiction, reservoir engineering methods are used to estimate the exploitation process about the block, which including water drive curve method, the correlation experience method, the method of the flow pipe budgetary estimate and the method of well net density. on the basis of these method, the author studied the macrocospical distributing of remaining oil in each layer

    針對單元開發過程中存在的突出矛盾，運用水驅曲線法、相關經驗公式法、流管概演算法、合理井網密度法等油藏工程方法對斷塊的開發歷程進行評價，在此基礎上進行各小層剩餘油的宏觀研究。
  5. The engineering drilling machine of kp2200 type is double layers bottom plate, and drives through hydraulic pressure, upper plate can move fore and aft on the lower plate, the drill power leans back under the action of oil cylinder, the lower plate can put the drilling tool within 2. 5 meters into well hole without moving, it is convenient and reliable, and ensures construction quality

    Kp2200型工程鉆機為雙層底盤，通過液壓驅動，上盤可在下盤上前後移動，鉆塔在油缸的作用下後仰，下盤不動即可把2 . 2米以內的鉆具放入井孔內，方便可靠，保證施工質量。
  6. Hydraulic driving system performance is stable, its control and adjusting is convenient and it is safe and reliable. using the synchronous display of the curve of oil pressure and wheel speed and the flash of the control principle. it implements the real synchronous depict of abs word process and control result

    液壓驅動系統性能穩定、控制調整方便、工作安全可靠，利用油壓與輪速曲線及控制原理動畫的同步顯示，實現了對abs系統工作過程及控制結果的真實、實時描繪。
  7. Chapter two constructed the mathematical model of robot and its environment solved by the fem analysis. the functions or relations between the robotic parameters and its drive forces, thickness or its velocities were given, and also the functions or relations between the environment and the robot force, friction, robot velocity, minimum thickness of film or sustain force of dynamic films were given

    論文第二章通過建立機器人和環境的數學模型，利用有限元方法求解其中的n - s方程，得出管道中微型機器人的各種設計參數與機器人的驅動力、形成的最小潤滑油膜厚度和機器人的運行速度之間的關系曲線，研究了管道環境與機器人驅動力、摩擦阻力矩、機器人運行速度、形成的最小潤滑油膜厚度、油膜的承載能力之間的關系。
  8. In the course of remaining oil, macrofactors have four controlling function on microfactors, which determine pore structure and wettability of oil stratum, offer dynamic force to water drive oil, control its process and influence its velocity

    剩餘油形成過程中，宏觀因素對微觀因素有4個方面的控製作用，它們決定油層孔喉結構及潤濕性，提供水驅油動力，控制水驅油過程，影響水驅油的速度。
  9. Aiming at characteristics of serious conflict among layers, thin layers developed and scattered distribution of remaining oil, this paper introduces techniques of non - gel fracturing, multi - fractures fracturing, large discharge capacity and large sand amount fracturing, thin layer fracturing and high effective return discharge

    摘要針對大慶油田薩南開發區三類油層層間矛盾突出、油層發育薄及剩餘油分佈零散等特點，根據油藏精細地質研究成果，通過個性化壓裂設計，在試驗區三類油層聚驅挖潛過程中，應用了非凝膠壓裂、多裂縫壓裂、大排量及大砂量壓裂、薄隔層壓裂以及高效返排壓裂等配套的工藝技術。
  10. The result indicates that displacement characteristics of unsheared polymer solution is better than the same viscosity polymer solution after sheared, the injection pressure of the unsheared polymer solution is higher than the same viscosity polymer solution after being sheared in the same permeability core, the lower the permeability, the bigger the molecule weight and the bigger the difference, as to the every layer of the secondary oil layer, it is feasible to displace oil with the polymer solution after sheared, and the eor of the polymer flooding can increase more than 9. 84 %

    結果表明：未經剪切的聚合物溶液的驅油效果好於經剪切之後的相同相對分子質量的聚合物溶液的驅油效果；對于相同滲透率的巖心，未經剪切的聚合物溶液比經過剪切相同相對分子質量聚合物溶液的注入壓力高，而且滲透率越低，相對分子質量越大，差異越大；對於二類油層的各滲透率小層，進行經剪切后聚合物溶液驅油是可行的，聚驅采出程度提高幅度均超過9 . 84 % 。
  11. By using the hydraulic torque converter to drive the mud pump, both the prime motor and the working machine can be protected, and the pump pressure can be controlled in the whole course of drilling if the rated rotary speed of the diesel engines is kept

    通過液力變矩器驅動鉆井泵可同時保護原動機和工作機；在保持柴油機額定轉速的條件下，可實現泵壓的全過程式控制制。
  12. This paper studies the effect of oil property on the formation of super - low interfacial tension from asp system in asp process, and get some important recognition providing assistance for further study on the mechanism of asp flooding

    著重研究了在三元復合驅過程中，原油性質對於三元體系形成超低界面張力的影響，得到了一些有意義的認識，為今後研究三元復合驅油機理提供了新的思路。
  13. Abstract : this paper studies the effect of oil property on the formation of super - low interfacial tension from asp system in asp process, and get some important recognition providing assistance for further study on the mechanism of asp flooding

    文摘:著重研究了在三元復合驅過程中，原油性質對於三元體系形成超低界面張力的影響，得到了一些有意義的認識，為今後研究三元復合驅油機理提供了新的思路。
  14. In the sixth chapter, on the base of the development of the card reader driver and link to the fashion technology of the device driver development named wdm, the paper makes some studies in the methods and the realizations and some settlements for the pivotal technology of wdm driver development. at last, the paper gives some summarizations and some prospects

    第六章在對加油站自動化系統讀卡機驅動程序開發的基礎上，結合當今流行wdm驅動程序開發技術，詳細闡述了基於wdm的驅動程序設計方法、實現過程和其中一些關鍵技術，最後對本篇論文進行了展望與總結。
  15. It can settle the over heat problem of engine and too much power consumption and hydraulic oil system which often happens in the construction machinery engineering construct process. the control system is composed by egine cooling system and hydraulic cooling system, which can control the two part at the same time. the cooling fan can be disposed at anywhere which conquer the abuse of tradional drive style and use low power. the electric and hydraulic mix - drive cooling system settle the over heat problem of engine and hydraulic oil system effectively

    針對工程機械在施工過程中經常出現發動機過熱、液壓傳動系統液壓油冷卻不足和耗能大等問題，本文設計了一種新型的電液混合驅動冷卻裝置控制系統。本系統將原冷卻系統分成發動機冷卻系統和液壓傳動冷卻系統兩個相對獨立的部分，發動機冷卻系統利用液力驅動，液壓油冷卻系統利用電動機驅動，控制系統由一片單片機同時對兩個冷卻系統進行控制。
  16. In light of the current state of the gas station system, based on analyzing the requirement of the daily work of the gas station and considering its requirement in the future, the paper introduces the development and implementing of the gas station automation system with management and monitoring functions. the general theories of software engineering and systemic engineering and mis are used. furthermore, the paper makes some studies of the device driver development of windows driver model

    該文針對當前加油站系統的現狀，在詳細分析加油站系統日常工作功能需求和考慮未來發展需求的基礎上，運用軟體工程、系統工程與管理信息系統開發的一般理論和軟體開發的基本方法，介紹了集監測與管理於一體的加油站自動化系統的設計、實現過程，並在此基礎上對基於wdm驅動程序開發做了一些研究。
  17. It performs a large amount of physical simulation experiment using the multi - function displacement equipment which is imported from american temco company and summarizes the effecting rule of the injected alternating slug size on the displacement efficiency during the alternating injection of gas and liquid. it uses orthogonal method to study the set and type of pre - slug and post - slug and their effect on the displacement efficiency of foam flooding and optimizes the main and sub - slug size so as to decrease the cost while keeping a high displacement efficiency

    通過從美國temco公司引進的多功能驅替設備，所做的大量的物理模擬試驗，總結出了氣液交替注入時，注入交替段塞的大小對驅油效率的影響規律，利用正交設計法研究了前後段塞的設置與否及種類對泡沫復合驅驅油效率的影響程度，還對主次段塞的大小進行優化，在保證較高的驅油效率的前提下降低成本。
  18. The second part mainly exploits and manufactures the wheel driving style, the detection and display of braking oil pressure and the wheel speed as braking control process synchronous

    第二部分主要是對車輪的其驅動方式、制動油壓的檢測與顯示、輪速的檢測與顯示、制動控制過程的實時檢測與顯示等內容進行了開發與研製。
  19. The oil - field ' s basic geology characteristic and develop characteristics to come to a decision that water drive lead to serious of unbalanced in oilfield development. the situations of unbalanced water drive lead to serious watered out of oil formation in horizontal section. the strength of water drive is varying from in every oil formation of the same oil block and the same oil layer in different block

    油田的基本地質特徵及開采特點決定了注水開發過程中水驅存在嚴重的不均衡性，導致平面上嚴重水淹，層間的水驅動用狀況存在較大差異，不同油層和不同區塊的同一油層水驅程度差異較大，剩餘油分佈狀況異常復雜。
分享友人
分享到 Line

分享到臉書