高壓油管路 的英文怎麼說
中文拼音 [gāoyāyóuguǎnlù]
高壓油管路
英文
high pressure oil pipeline- 高 : Ⅰ形容詞1 (從下向上距離大; 離地面遠) tall; high 2 (在一般標準或平均程度之上; 等級在上的) above...
- 壓 : 壓構詞成分。
- 油 : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
- 管 : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
- 路 : 1 (道路) road; way; path 2 (路程) journey; distance 3 (途徑; 門路) way; means 4 (條理) se...
- 高壓 : 1 (殘酷迫害; 極度壓制) high handed 2 [氣象學] (高氣壓) high pressure3 (高電壓) high tension...
- 管路 : pipeline; canal; channel
-
Excessive pressure may develop in the tank because of plugged or pinched lines or from a plugged liquid vapor separator or charcoal canister.
由於管路堵塞,壓癟或油氣分離器和活性炭罐被堵塞,油箱里會產生過高的壓力。A new method was introduced for testing the fuel injection law of diesel engine via neural network on the basis of the calculation of the pressure waves measured by a sensor clamped on the high - pressure tube of a diesel engine
對用外卡式壓力傳感器測量的柴油機高壓油管壓力波計算噴油規律的方法進行分析,提出了利用人工神經網路檢測柴油機噴油規律的方法。Road vehicles. fuel injection pumps. high - pressure pipes for testing
道路車輛.燃油噴射泵.試驗用高壓管The construction of conical nozzle is used by pump ' s delivery - valve, making use of the dynamic characteristics of conventional. short pipe to enhance injection pressure. there are three parameters of fuel injection system : response pressure, injection - advanced angle, injection valve bulge high degree, the best match was found by adjusting them
在油泵出油閥端,採取漸縮管結構措施,利用管路動態效應提高噴油壓力;對于噴油系統參數:噴油壓力、靜態供油提前角和油嘴凸出高度,三個參數進行調整試驗,找到它們的最佳匹配。Full - sealed assembling capacitor is applied to ac power sys - tem 50 60hz with rated voltage of 6kv 10kv 35kv for improving power factor and quality of power grid, reducing transmission loss and raising the efficiency of transmission transformation faciliti - es. this type of capacitor has an assembling full - sealed struc - ture, and it is comprised of capacitor unit body, container, insula - ition cooling impregnant, outlet ceramic bushing, pressurereleas -
額定電壓6kv 10kv及35kv的交流電力系統中用來提高功率因數改善電網質量,降低線路損耗,充分發揮輸變電設備效能。本產品為裝配式全密封結構。主要由器身波紋油箱絕緣冷卻油出線套管壓力釋放閥溫度控制器等部件組成。分享友人