高壓注水 的英文怎麼說

中文拼音 [gāoyāzhùshuǐ]
高壓注水 英文
high pressure water infusion
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 壓 : 壓構詞成分。
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 高壓 : 1 （殘酷迫害; 極度壓制） high handed 2 [氣象學] （高氣壓） high pressure3 （高電壓） high tension...
  1. The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation

    高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。
  2. In this thesis hydraulic experimental studies and theoretical analyses on the vortex - flow drop shaft were conduced and the following results were accomplished : ( 1 ) in the model test some hydraulic characteristics including the shape of air core in the center of the drop shaft, the radial distribution of water flow velocity and the distribution of pressure on the wall of the drop shaft were measured under the condition of high water head above 250m and large discharge above 1400m3 / s. ( 2 ) a kind of computational method for the spiral water flow in the air core region of drop shaft was discussed and applied and the results agree the experimental data well. ( 3 ) the total ratio of energy dissipation in the drop shaft can reach 90 % and the energy dissipation in every region was discussed quantitatively

    本文通過試驗研究與理論分析對旋流式豎井泄洪洞應用於高水頭、大泄流量情況時存在的一些水力學問題進行了研究和探討，取得以下主要成果：一、結合小灣工程導流洞改建，對高水頭（ 252m ） 、大泄流量（ 1400m ~ 3 s ）條件下旋流式豎井中的水流運動特徵進行了比較全面的測量，包括空腔形態、徑向流速分佈及井壁壓強等；二、提出了豎井空腔段螺旋水流水力計算方法，其計算結果與實測值吻合良好；三、利用試驗與計算結果，對旋流式豎井的消能機理進行了探討，對豎井各部分的消能能力有了總體認識；四、對豎井下部消力井的合理井深進行了優化試驗研究，發現消力井合理深度為0 . 9d左右；五、通過試驗研究，歸納出豎井水流總摻氣量估算方法，為導流洞排氣方案的設計提供了參考依據；六、在高水頭、大流量條件下，豎井空腔段下部流速很高，盡管水流螺旋運動引起的離心力可以確保井壁壓強保持正壓，但空化數依然較低，因此豎井的空化空蝕始終是工程界關注的重大問題。
  3. The question about burning method existing in spraying high pressure steaming in chamber is analyzed. the principle and character of auto supplying water, additive, steaming and combustion - support technology are introduced, also the economic benefit is analyzed

    分析了傳統爐膛內噴射高壓蒸汽燃燒方法存在的問題，介紹了鍋爐全自補水加劑注汽助燃技術的機理、特點。
  4. The paper points out that the reasons for displacement efficiency improving of pressure coring well are as follows : firstly, extra - high injection multiples ; secondly, extra - low critical drive ratio ; thirdly, high velocity fluid ' s big differential pressure drive during the process of coring

    得出導致礦場密閉取心井驅油效率高的原囚：一是特高的注水倍數，二是特低的臨界驅動比，三是取心過程中高黏度流體的大壓差驅動。
  5. There are many methods of foundation consolidation for civil engineering, such as soil exchange method, prepress method, dynamic consolidation method, vibrancy rushing method, soil and podsol dense pile method, sand pile, cement - coal - powder and gravel pile method, deep mixing method, high - pressure eject masonry, etc. the dynamic consolidation and deep mixing method ( dmm ) are very common in project construction

    目前國內外地基處理的方法很多，主要的地基處理方法包括：換填法、預壓法、強夯法、振沖法、土和灰土擠密樁法、砂樁法、水泥粉煤灰碎石樁法、深層攪拌法以及高壓噴射注漿法等。其中強夯法和深層攪拌法是工程建設中較常用的加固方法。
  6. Through analyzing the structure of open caisson, and according to sinking stress principle, the paper introduced in the open caisson construction process sinking, correcting error, survey control as well as peculiar circumstance processing technical measure, such as in open caisson construction the inner - mold for sanding, framework supporting and steel binding, and concrete casting ; in open caisson sinking - control the sand in edge foot inner - mold, sand - pumping sinking, and pressure hydraulic monitor breaking and pressure - blowing sinking by air pressure blower etc

    摘要根據下沉受力原理，分析了沉井結構，介紹了沉井施工過程中的下沉、糾偏、測量控制以及特殊情況處理的技術措施，如沉井製作中的填沙內模，模板支設和鋼筋綁扎，混凝土澆注；沉井下沉控制中的刃腳內模沙土，抽沙泵抽沙下沉，高壓水槍破壓、空壓機吹壓下沉等。
  7. Ghg - electrical grade activated silica powder is produced by way of mingling on the basis of electrical grade silica powder. it has activt effect on surface & make silica powder mingled with resin, raise cohesive force between resin & silica powder, raise the water - resestance on the sunface and the compressive strength of pour object, reduce sediment, gradation & split, increase filler of silica powder, and replaced inpoted products on the producing line of imported dry type transfomer & high tension mutual induc tance equiment, it has been the best pouring insulate materual in electrical trade

    電工級活性硅微粉是在電工級硅微粉的基礎上進行偶聯化處理而製成，具有表面活性作用，能使用硅微粉與樹脂發生交聯，提高樹脂與硅微粉的粘結力和界面增水性，提高澆注體抗沖擊強度，減少沉澱、分層、開裂現象，增加硅微粉的填充量，在引進的乾式變壓器、高壓互感器生產線上已成功地代替了進口產品，成為電工行業理想的環氧澆注絕緣材料。
  8. Abstract : a certain hall is demaged by water. lime pile and high compress forcing pulp are used to reinforce fhe settled foundation

    文摘:某禮堂綜合樓受浸水損壞，採用生石灰樁及高壓水泥注漿綜合法加固建築物沉陷部分地基，獲得成功。
  9. The analysis of excess pore water pressure generated by high pressure jet grouti ng

    高壓噴射注漿法產生的超孔隙水壓分析
  10. It has been proved that the design and construction organization presented in this thesis for the strata consolidation by means of high pressure shot grouting method be a success, and the design procedure and construction scheme can provide a guide for soft foundation treatment and waterproof in underground engineering

    實踐證明，高壓噴射注漿法地層加固的設計和施工組織是成功的。本文提出的設計思路和施工組織方案對地下工程軟地基處理和防水止滲具有指導意義。
  11. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  12. Abstract : the paper mainly introduces the application that the high voltage inverter in the oil field pump and joint electricity effect is clear, and possesses application and dissemination value

    摘要：本文敘述了高壓變頻器在油田注水泵上的應用，節電效果明顯，具有推廣應用價值。
  13. The background of this dissertation is based on a project of researching and developing a high voltage series h - bridge multilevel converter, which drives an induction motor of 6300v, 2240kw for driving a water flooding pump in taigang. the research work on high voltage high power series h - bridge multilevel converter has been carried out by theory analysis, computer simulation and experiments

    本文以太鋼某廠額定功率2240kw ，額定電壓6300v注水泵電機變頻調速科研工程為背景，從理論分析、計算機模擬和裝置實驗幾方面入手，對高電壓大容量串聯h橋多電平變頻器的理論和工程應用技術進行較深入研究。
  14. The result of long - term operation shows that the computer control system is practical and effective, it can run in the optimal state within a long duration to fully realize data collection and process, remote data transmission and vfvs constant injection control of pumps. it speeds up the automatic procedures of the seawater treatment process, really realizes the unmanned working, decreases the physical intensity to a large extent, improves the management, enhances the management level, avoids equipment wear down as much as possible, makes the seawater treatment efficient and lessens the cost of production

    長期的運行結果表明，該計算機控制系統的實施切實有效，既成功實現了對被檢測參數的數據採集與處理、遠傳以及注水泵機組的變頻調速恆壓注水控制，又提高了系統的自動化程序，真正實現了無人值班作業，在很大程度上降低了工作人員的勞動強度，極大的改善了現場的管理狀況，提高了生產管理水平，且有效避免了設備損耗，提高了水處理效率，降低了生產成本。
  15. Application of threefold high - pressure jet grouting in construction of waterproof curtain

    三重管高壓噴射注漿進行隔水帷幕的應用
  16. Application of high pressure injection water at combined mining face

    高壓注水在綜放工作面的應用
  17. Technical regulation of design for high pressure water injection fittings

    高壓注水管路配件設計技術規定
  18. Developing low permeability reservoir efficiently by high pressure water injection

    合理應用高壓注水技術開發好低滲透油藏
  19. Numerical simulation study on the high - pressure water injection into coal seam in muchengjian coal mine

    木城澗礦煤層高壓注水的數值模擬分析
  20. According to the analyses of the research results about the feasibility of 4 - d seismic and the successful 4 - d seismic cases of foreign companies, the author put forward the suggestions for 4 - d seismic pilot area selection ; briefly analyzed the influential function of producing way on the seismic response ; utilized theory calculation, coring data analyses, and reservoir numerical simulation to define the fluid substitution effects on the p - wave velocity. through long time water driven to the reservoir, some of the properties and the log curves have changed, the author tried to find the variation rule of the reservoir and its effects on seismic velocity. the " blind point " in 4 - d seismic feasibility study both in china and overseas was found, that is the lack of consideration of the influence of physical property variation by long time water driven on the seismic response

    在深入分析國外四維地震可行性研究成果和成功實例的基礎上，提出了有利於水驅四維地震成功的工區優選條件；簡要剖析了各種開采方式及其對地震特性的影響；利用理論計算、巖心分析、油藏數值模擬三種方法確定了流體替代對縱波速度的影響；通過對長期水驅造成的物性參數、測井曲線以及油藏溫度和壓力變化規律的總結，分析了這些變化對地震速度的影響，指出了目前國內外水驅四維地震可行性研究中存在的盲區?沒有充分考慮長期注水造成的物性、溫度和壓力變化對地震響應的影響，完善了水驅四維地震可行性研究的內容；在考慮了這些變化因素后，高29斷塊水驅四維地震可行性研究結果表明：四維地震監測注水前沿可能要比監測油藏變化容易的多；以四維地震巖石物理可行性研究結果為基礎，提出了五個有助於突出四維地震造成的微小差異的途徑，為今後水驅四維地震研究指明了方向。
分享友人
分享到 Line

分享到臉書