高拉力強度 的英文怎麼說

中文拼音 [gāolālìqiángdù]
高拉力強度 英文
high tension
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 拉 : 拉構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 拉力 : pulling; pulling force; thrust; traction; tension拉力表 draw bar [pull] dynamometer; 拉力測定儀 [...
  1. It canbe determined the enhancing effect of new steel fiber to shear resistance of beams by the test of tensile strength of steel fiber reinforced concrete, it is important to reduce test cose and increase research efficiency

    可以通過鋼纖維混凝土抗拉強度試驗來確定新品種鋼纖維對梁斜截面上混凝土受剪承載力的增強作用，這對于降低試驗成本和提高研究效率具有重要工程價值。
  2. With the filling of diabase, the mechanical properties of the composite increased first and then decreased with a top tensile strength of 56. 5mpa and a top impact strength of 70. 1mpa. these illuminated that the diabase fiber reinforced pvc composites could be used as structure materials

    復合材料的力學性能隨著輝綠巖的增加先升后降，復合材料拉伸強度最高可達56 . 5mpa ，復合材料沖擊強度最高可達70 . 1mpa ，說明輝綠巖纖維增強pvc復合材料作結構材料使用。
  3. The results from x - ray diffraction demonstrated that pp / mmtome was a fully intercalated nanocomposite, pp / mmtom and pp / ommt were partly intercalated nanocomposites, but the intercalation effect of pp / mmtom nanocomposite was better ; the crystallization characteristics of pure pp and pp / mmt nanocomposites were investigated by dsc, waxd and pom. the result of these testing showed that mmt nano - layers acted as nucleating agents for the crystallization of pp, the addition of mmt had effect on the crystallization process, leading the increasing of crystallization temperature crystallization rate and crystallinity, but also the dimension of spherulite reduced. but the formation of pp crystal did n ' t change, the formation of pp crystal in three pp / mmt nanocomposites and pure pp were a - form on the whole ; influences of three sorts of mmt on mechanical properties of pp / mmt nanocomposites were studied, as a result, the addition of mmt comprehensively improved mechanical properties of pp : notched impact strength, tensile strength and flexural properties were all increasing, but the extent of increasing were n ' t large

    通過xrd分析比較這三種pp mmt納米復合材料微觀結構得到， pp mmt _ （ ome ）屬于完全插層， pp mmt _ （ om ）與pp ommt的插層程度相近，但是pp mmt _ （ om ）相對較好；通過對純pp和三種pp mmt納米復合材料的結晶性能研究發現，蒙脫土納米片層對pp結晶產生明顯的異相成核作用，結晶能力增強，使pp的結晶溫度和結晶速率提高，結晶度增加，球晶晶粒細化，但是沒有改變pp的結晶形態，三種pp mmt納米復合材料的結晶形態都屬于晶；通過對pp mmt納米復合材料的力學性能測試得知，蒙脫土的加入全面提高了pp的力學性能，缺口沖擊強度、拉伸強度和彎曲性能都有一定程度的提高，浙江{ _業大學碩十學位論文摘要但是提高幅度都不是很大，不過ommt 、 mmtom和mmtc ） me三種蒙脫土對pp力學性能有著不同的改性作用，其中pp / mmtom最好， pp月邊mto崛次之， pp / ommt最低，這種情況主要是由蒙脫土對pp結晶性能的影響和蒙脫土的納米改性作用造成的。
  4. Results of study show that inception voltage of electrical tree, breakdown voltage, environmental stress cracking, tensile strength and elongation at break of low density polyethylene are improved after grafting

    研究結果表明：接枝聚硅氧烷后，改性的低密度聚乙烯的樹枝引發示性電壓、擊穿場強、耐環境應力開裂性、拉伸強度及斷裂伸長率都得到提高。
  5. The ultrasonic impacting has very good effect of adjusting residual stress, improving texture and raising fatigue strength of structural element, and it is particularly helpful to eliminate tensile stress in the shallow layer thereof

    摘要超聲波沖擊對于調整殘余應力、改善組織、提高疲勞強度都有很好的效果，特別對消除淺層拉應力有很大的幫助。
  6. Tensile strength and elongation, weight, elasticity, resistance to flammability and high heat levels, moisture - transport capabilities, durability, and weatherability are some examples of attributes that could be included in a technical textile performance specification

    拉伸強度、抗張伸展率、重量、彈性、耐燃性、耐高熱水平、水分輸送能力、耐久性和耐候性都包括在技術紡織的性能規范中。
  7. Second, many mechanical properties are tested, for example, tensile strength and tensile modulus, flexural strength and flextural modulus and impact strength. by the analysis of the tensile stress - strain curves and the flexural stress - strain curves, the results are as follows : 1 ) the voluminal content of fibre of composite making by vacuum assistant resin injection is more than other composites. 2 ) the mechanical properties of the needlepunching nonwoven fabric reinforced polymer composite are superior to these of the calendering nonwoven fabric reinforced polymer composite

    首先，採用不同的增強材料（針刺非織造布和熱軋非織造布） 、不同的基體材料（ 961樹脂和306樹脂）和不同的成型工藝方法（手糊法、真空袋法和真空輔助成型法）製造出了一系列非織造布增強復合材料，然後對它們的拉伸強度、拉仲彈性模量、彎曲強度、彎曲彈性模量和沖擊強度等力學性能進行了測試，並分析了它們的拉伸載荷? ?位移曲線和彎曲載荷? ?位移曲線，結果表明真空輔助成型工藝能大大提高纖維的體積含量；針刺非織造布增強復合材料各項力學性能優于熱軋非織造布增強復合材料。
  8. Condoms will age as time goes by, resulting in impairment of the tenacity. exposure to intense heat and light will also accelerate ageing of the rubber, thus weakening the pulling force and affecting its overall function. do not buy condoms displayed under decorative light and sunlight in the shop

    安全套在出廠之後，會隨著時間而出現老化現象，影響其韌力，高熱或強光也會令橡膠加速老化，拉力強度變弱，以致影響其功能，在選購時，如產品存放于射燈或陽光照射的地方，便不應購買，安全套應放置在陰涼的地方。
  9. The test result of the rene95 sample showed that the maximum ultimate tensile strength can be as high as 1400mpa and has reached 97. 9 % of that of the sample fabricated by powder metallurgy ( pm ). the plastic elongation of the test sample can even exceed that of pm. the ultimate tensile strength of the test sample grown from single crystal substrate has surpassed 6 % of that of grown from the stainless steel substrate, at the same time the plastic elongation surpassed 40 %

    對成形試樣的力學性能測試結果表明，強度方面_ b最大為1400mpa ，已經達到了粉末冶金的97 . 9 ，塑性方面甚至超過了粉末冶金的水平；以單晶為基材的成形試樣其最大拉伸強度要比不銹鋼為基材的試樣高6 ，延伸率要高40 。
  10. Compared with those of as - sprayed ring, hardness and tension strength of area near processing face are increased by 45 % and 40 % respectively. friction mechanical performance of the ring is improved at large extent, and especially the wearing amount is merely 13 % of as - sprayed rings. after dual - direction cyclic pressing, the pore - closed state and the distributing of density and hardness are nearly identical in every part of ring. the friction mechanical property is close to that of single - direction - cyclic - press ring

    靠近壓力加工面部位，硬度較沉積坯提高了45 % ，拉伸強度較沉積坯提高了40 % 。雙向楔壓后孔洞閉合、密度硬度分佈都比較均勻。單向楔壓后，用壓力加工面作為摩擦面， al - 20 % si / sicp復合材料的摩擦磨損性能得到大幅度提高，尤其磨損量為楔壓前的13 % 。
  11. Simultaneity, various single fiber strength tests ( sft ) and the single fiber fragmentation techniques were discussed, and the influence of fiber surface treatment on the single fiber strength and the interface load - transfer were discussed in detail. the two parameters weibull statistic theory was used to evaluate the scattering of the tensile strength test results of three types of single fibers with different surface treatments. the following conclusions can be drawn based on the analysis of the results

    同時，文中詳細討論了單纖維強度測試實驗（ sft ）和單纖維復合材料斷裂實驗（ sfc ） ，重點討論了纖維表面處理對單纖維拉伸強度和界面載荷傳遞能力的影響；採用兩參數weibull統計理論對經過三種不同表面處理的單纖維拉伸強度的測試結果的分散性進行了評價，獲得了理想的實驗結果；分析實驗結果可得到如下結論， sft實驗與sfc實驗獲得的界面剪切強度吻合良好；經過表面處理的玻璃纖維的界面粘結情況較未經處理的玻璃纖維好；經過表面處理的玻璃纖維的界面粘結強度和單纖維拉伸強度均高於未經表面處理的玻璃纖維。
  12. Bearing capacity and displacement are two main problems in the application of geotechnical engineering. based on a series of pull - out tests using three kinds of paper and a sort of window screening as geogrid, twenty - seven in limit and several in working - stress geogrid - reinforced slope model tests designed through orthogonal principle have been conducted to have obtained the relationship between the bearing capacity and four factors ( i. e. reinforcement, angle of reinforced slope, the designed - length of reinforcement and the distance between layers of reinforcement ). the law of slope lateral ( horizontal ) displacement versus to the height of slope vary with external - load was derived from the model test data, and the main factor affecting the lateral and vertical displacement of geogrid - reinforced slope was obtained through analysis

    承載力（強度）和變形是巖土工程應用領域的兩大主要問題，本文以紙和窗紗布模擬加筋土邊坡的土工格柵，在一系列拉拔試驗的基礎上，以正交設計理論分別安排27個極限應力狀態和若干個工作應力狀態加筋土邊坡模型試驗，並以模型試驗獲得的數據為依據，採用誤差、極差及回歸分析方法，探討了加筋土邊坡承載力與筋類、筋長、層間距、坡角4因素的相關關系，獲得了在外荷載作用下加筋土邊坡的側向位移隨坡高的變化規律（並進行了定性解釋）和坡頂的豎向位移特性，並分析其主要控制因素。
  13. Experiment results show that, with the increase of frequency and swing, the dispersing, physical and flame retardant performances are improved greatly, tension strength, impact strength and oxygen index have increased about 32 %, 39 % and 10 %, and finally arrive a steady value

    實驗結果表明：隨著振動頻率和振幅的增加，無機阻燃劑的分散性能、製品的力學性能和阻燃性能也會相應增加，拉伸強度、沖擊強度和氧指數可分別提高約32 % ， 39 %和10 % ，但其增加的速度是逐漸減少的，並最終達到一個穩定值。
  14. Making up nanopaint mixed with nano - silica, the improvement of its properties has been tested. the mechanic property of membrane formed increased, such as tensile strength, elongation at break, surface rigidity ; the scrubbing resistance and stain resistance of the paints has been improved. but it ' s the limitation that ideal results of properties of waterproofing and uv - screen have n ' t been gotten

    實驗結果表明，塗膜的力學性能得到提高，如拉伸強度、斷裂延伸率和表面硬度；塗料的耐洗刷性能和耐沾污性能有改善，但防水性能和抗紫外性能無明顯改善，接觸角和吸水率數據無規律可循。
  15. The izod impact strength was increased 48 % and the tensile strength was increased 12 % contrast with pure pp, achieved the highest value when 3 % nano - sio2 by weight modified with silicone coupling agent and pp - g - mah was added

    加入3納米sio _ 2粒子，復合增容劑5份時復合材料力學性能最佳，相比純pp其沖擊強度提高48 、拉伸強度增加12 。
  16. When sintered at 1050c, the wear resistance of the composites were better than that of the ferroalloy under both low and heavy load without oil lubrication. the wear resistance, hardness, and other mechanical properties of the composites with nickel coated sic were better than those of the composites with bare sic particles. however, when sintered at 1100c, interfacial reaction became so acute that the properties of the composites with nickel coated sic particles was worse than those of the composites with bare sic particles

    試驗結果表明：與鐵合金相比，在1050時燒結時，加入適量的sic后，耐磨性有較大的提高；而且加入鍍鎳sic的復合材料的耐磨性、硬度和拉伸強度等力學性能比加入相同含量的未鍍sic的材料的性能要好；在1100燒結時，由於界面反應的加劇，含有鍍鎳sic材料的性能反而比含有未鍍sic材料的性能差。
  17. The results of comparison showed that when the content of fillers was from 3 to 10 parts, the mechanical property of nbr / layered silicates nanocomposites is higher than that of carbon black reinforced rubber. the tensile strength of nanocomposites was 1. 84 times of carbon black reinforced rubber, and the tear strength was 1. 49 times

    研究結果表明：當層狀硅酸鹽的用量在3 - 10份范圍內時， nbr /層狀硅酸鹽納米復合材料的力學性能遠遠高於同量炭黑補強膠料的力學性能，拉伸強度最高是炭黑補強膠料的1 . 84倍，撕裂強度最高是炭黑補強膠料的1 . 49倍。
  18. With 20 % coupling agent, composites with 40 % and 50 % wood - flour content gain better storage moduli ( e " ) than these without coupling agent, and composites with 40 % and 50 % wood powder content attain the increments in tension and bending strength of 10 % and 40 % respectively, the rotate speeds of extruder affect the mixing of wood powder, coupling agent and polystyrene

    3 ）雙螺桿擠出機的轉速影響著木粉偶聯劑和聚苯乙烯的均勻混合程度。研究發現，雙螺桿轉速為40rpm時，復合材料性質好於其它轉速。 4 ）木粉含量為40 ，偶聯劑含量為20的復合材料其力學強度（拉伸強度為40 . 22mpa ，彎曲強度為76 . 192mpa ）和存儲模量明顯高於其他工藝條件的復合材料。
  19. Pes is a good membrane materials which possess excellent properties, such as high mechanical strength, good chemical stability and resistance to heat, pressure and erosion, its temperature of glass transition is 225

    聚醚碸（ pes ）是一種綜合性能優良的聚合物膜材料，其玻璃化溫度高達225 ，具有較高的拉伸強度和優良的化學穩定性、耐熱性、耐壓力，耐腐蝕等性能。
  20. At present, at present, we have all our production lines automatically, and the annual output up to 80, 000, 000 pcs ; among which the nylon zipper is very popular in the market because of the tensile strength however, the plastic zipper make itself become as the mainstream in market because of its various colors and safety coefficient

    目前擁有皆為全自動化的生產線；其中尼龍拉鏈的拉力強度高，廣受好評，而塑鋼拉鏈由於色澤變化多，安全系數更高，已成為市埸主流。
分享友人
分享到 Line

分享到臉書