高溫熔燒 的英文怎麼說

中文拼音 [gāowēnróngshāo]
高溫熔燒 英文
high temperature heat
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Molten lead and iron boiled in the marble basin of the fountain ; the water ran dry ; the extinguisher tops of the towers vanished like ice before the heat, and trickled down into four rugged wells of flame. great rents and splits branched out in the solid walls, like crystallisation ; stupefied birds wheeled about and dropped into the furnace ; four fierce figures trudged away, east, west, north, and south, along the night - enshrouded

    熔化的鉛和鐵在噴泉的大理石盆里沸騰，燒幹了泉水滅燭器似的塔樓尖頂在高溫前像冰一樣熔化，滴落下來變作了四個奇形怪狀的火池堅實的墻壁以結晶的紋樣作樹枝形迸裂，迸出了巨大的豁口和裂縫。
  2. Our factory adopted high pure electric smelting mullite as main material, which is produced new size the best refuactory throught heat pressure and tem - - perature burning, it is suital ble for steel and ion, metallurgy and ceramics and is special suitable for stove top. stove wall and heat temper ature posmon of hot wind stove

    我廠採用高純電熔莫來石做主要原料經高壓成型和高溫燒成而制得的低蠕變磚是一種新型的高級耐火材料，適用於鋼鐵，冶金和陶瓷等行業，特別適用於熱風爐的頂爐墻及各高溫部位。
  3. Main products of huayao include ceramic roller kiln, tunnel kiln, glass furnace, metallurgical carbide furnace, baking furnace, coke oven, heat treatment furnace, cement kiln, brick kiln, boiler, crystallite glass kiln, high - temperature shuttle kiln, and etc

    陶瓷輥道窯、隧道窯，玻璃熔窯，冶金碳化爐、焙燒爐、焦爐、熱處理爐，建材水泥窯、磚瓦窯、鍋爐，微晶玻璃窯，高溫抽屜窯等均為拳頭產品。
  4. The results show that the sinters for the bf in shuicheng iron and steel co., ltd. have middle rdi ( low temperature reduction degradation index ), choice ri ( reduction index ), wider softening temperature range, high start melt and dropping temperature, smaller melt and dropping temperature range

    研究結果表明，水鋼燒結礦具有中等及中等偏下的低溫還原粉化性能和優良的還原性能；軟化區間偏寬，開始熔化溫度高和開始滴落溫度高，卻有較窄的熔滴區間。
  5. Then it is fired in a extremely hot stove

    接著陶器要在一個溫度極高的熔爐里燒烤。
  6. If coreless melting furnace mainly for steel ， alloy steel ， cast iron ， and other ferrous metal materials and stainless steel ， copper ， aluminum ， zinc and other non - ferrous metal materials melting ， melting with high efficiency ， energy - saving ， metal components uniform ， burning less temperature or block ， simple operation ， easy to supporting the advantages of production lines

    中頻無芯熔煉爐主要用於鋼、合金鋼、鑄鐵等黑色金屬材料以及不銹鋼、銅、鋁、鋅等有色金屬材料的熔煉，具有融化效率高、節電、金屬成分均勻、燒損少、溫升塊、操作簡單、易於配套生產線等優點。
  7. The high vacuum encapsulation of field emission display was realized with low - melting - glass encapsulation technology and high - temperature sintering process

    摘要通過採用低熔點玻璃封接技術和高溫燒結工藝，實現了穩定可靠的場致發射平板顯示器高真空封裝。
  8. Baseing on the request of low coercivity and high squareness in application, we had confirmed the main formulation of the lizn ferrite ; during the study of the conventional ceramic process, with the main formula foundation, we mainly studied the influence of ti4 +, co3 + on lowering coercivity and bi2o3, v2o5 on lowering sinter temperature. the results showed bi2o3 good characteristic on lowering sinter temperature and the sample which mixed with 1 % bi2o3 could reduce 40 % coercivity through slowing heating rate and extending the holding time

    在氧化物陶瓷工藝技術研究中，按實際應用中低矯頑力、高矩形比的要求，確定了lizn鐵氧體的主配方，在主配方基礎上進行了ti4 + 、 co3 +等離子對降低矯頑力的研究以及添加bi2o3 、 v2o5助熔劑對降低燒結溫度的研究，發現bi2o3具有優良的降低燒結溫度的特性，在添加bi2o3樣品燒結過程中，降低升溫速率，延長保溫時間可以降低40 %左右的矯頑力。
  9. Make sure there is no glaze on the bottom

    作品底部不能有釉，以免高溫燒熔后底部會造成破壞。
  10. Additions of carbon for improved slag resistance. spinel formation improves hot strength, slag resistance and brick joint erosion. 3 repairing material for bof uses fused magnesia or sintered magnesia as the main raw material and after modifid pitch and special additives are added, it has the following characteristcs than other conventional converter pitch temperature, shorter sintering time, longer service life and less pollution. it is mainly used for repairing converter working face, also for tapping side, tapping hole and bottom

    3 ，轉爐大面補料是採用電熔鎂砂或燒結鎂砂為主要原料，通過加入改性瀝青和特種添加劑使它和傳統瀝青補爐料相比具有高溫附著性好燒結時間短流動性好使用壽命長污染小等特點，主要用於修補轉爐迎鋼面通常稱「大面」也可以用於修補出鋼側，出鋼口及爐底等部位。
  11. Engineers believe that hotter boilers would raise yields even more

    工程師們相信升高熔爐的溫度還將進一步提升燃燒效率。
  12. Corundum mullite product adoprs electrocast refractories. through high pressure formation and high temperature burning, this product has comparatively high refractoriness, mechanical strength and slftening temperature under load. it can be widely used as inner lining. of various industrial furnace under such hard working conditions as high temperature, flushing and erosion

    剛玉莫來石製品是採用電熔合成原料，高壓成型，高溫燒成的具有較高耐火度及機械強度，較高荷重軟化濁的可廣泛應用於各類工業爐高溫、沖刷、侵蝕條件較苛刻的窯爐內襯的耐火製品。
  13. In this paper, a series of experiments are carried out with dlms for nickel - based metal powder materials, and the effect of process parameters in sample quality was investigated and analyzed. the main works are as following : ( 1 ) the effect mechanism of laser in metal powder and the nucleation mechanism are analyzed. ( 2 ) the process parameters that affect the quality of sintering parts are investigated and the way how they affect is clear

    本文基於直接激光金屬燒結成形技術，通過對鎳基高溫合金直接激光燒結成形的研究，從工藝角度研究某型號鎳基高溫合金的激光直接燒結成形性能以及工藝參數對燒結製件性能的影響，所完成的工作主要有: （ 1 ）分析材料與激光相互作用的機理及熔池的動態快速凝固過程。
  14. Magnesium - base alloys are easy to catch fire when heated at high temperature or melten, and this has become an obstacle to the developing of magnesium - base alloys. so, whether magnesium - base alloy can be used widely depends on the progress of the developing of the flame - resistant technique of magnesium - base alloys

    鎂合金在高溫下、尤其是在熔煉時很容易起火燃燒，這一缺點嚴重阻礙了鎂合金的發展，所以鎂合金的阻燃技術是關繫到鎂合金能否得到廣泛應用的關鍵所在。
  15. Application of high temperature air combustion technology to aluminum melting furnace

    蓄熱式高溫空氣燃燒技術在熔鋁爐上的應用
分享友人
分享到 Line

分享到臉書