齒根圓 的英文怎麼說
中文拼音 [chǐgēnyuán]
齒根圓
英文
dedendum circle-
The undercut controlling of involut cylinder gear shaving
漸開線圓柱齒輪剃齒過程中的根切控制Witch has worked out the tooth shape of datum rack and computer simulation of gear manufacture. pointedness, undercut and tooth tip becoming sharp are analysed. tooth thickness calculation and measurement, superposition coefficient calculation and belt length calculation are resolved
2 、給出了基準齒條的齒廓形狀，進行了齒輪加工計算機模擬，分析了可能出現的稜角問題，進行了齒輪內齒頂圓的求解、根切問題分析、齒厚計算與測量、齒頂變尖的分析、重合度的計算、帶長度的計算及齒輪設計的程序編制等。Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve
建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。A mathematical model for gear shaping was presented for machining of externally meshed non - circular gears with shaping procedure in terms of the positional relationship between the tool ( cutter ) and gear ' s pitch curve
摘要根據范成法加工外嚙合非圓齒輪時刀具和齒輪節曲線間的位置關系，提出了插齒加工的數學模型。Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments
文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。Measurement and instrument of addendum circle and dedendum circle diameter of odd tooth gears
奇數齒齒輪齒頂圓與齒根圓直徑的測量及其量具Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2The effect of the corner radius on root stress of involute gear
刀尖圓弧半徑對漸開線齒輪齒根應力的影響Hot rolled steel equal flange tees with radiused root and toes - dimensions and tolerances on shape and dimensions
帶圓角齒根和齒頂的熱軋鋼等邊二層交錯凸緣.尺寸和形狀及尺寸公差After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125
以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。Cylindrical gears - iso system of accuracy - part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
圓柱齒輪. iso精度體系.第1部分:齒輪嚙合對應齒根面的相應偏差定義和容許值Cylindrical gears. iso system of accuracy. part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
圓柱齒輪. iso準確度體系.第1部分:與齒輪齒對應齒根面有關的偏差的容許值和定義Abstract : this paper derives thecalculating formulas to the contact strength and oil - film thickness of the involute spur gear according to hydrodynamic lubrication principle. through check with test, shows that they may rully replace now available hertz formula and dowsonformula respectively
文摘:根據流體動力潤滑原理，推導出了漸開線直齒圓柱齒輪接觸強度及油膜厚度的計算公式，通過實驗驗證，說明它們可以完全分別代替現有的赫芝公式及通森公式。The critical error has been found through computation, which is the error circling the gear. the load sharing characteristics of two kind of star - type gearing train has been determined through comparison. based on computation, the load sharing capability of two - stage external gear train is better than that of two - stage internal and external gear train
其次，從靜力學的角度分析了各誤差對系統均載性能的影響，比較了各誤差對系統均載性能影響的大小，得到了較大的影響系統均載的誤差因素，即圓周方向分佈的誤差；比較了兩種星型齒輪系統的均載性能，根據計算結果，兩級外嚙合傳動系統的均載性能要好於兩級內外嚙合傳動系統。On the basis of selecting such assignment range of gear module and eccentricity that there would be no undercut for shaping the teeth of noncircular gears, dynamically graphic simulation of the shaping process was conducted on the computer by using the mathematical model developed
在分析范成加工外嚙合非圓齒輪不根切的模數、偏心率取值范圍的基礎上，根據所建模型將加工外嚙合非圓齒輪的范成過程用計算機進行了動態圖形模擬。In the solid model building program, based on the cutting tooth theory of double circular arc profile spiral bevel gear and autocad software, a series of computer simulations about solid model building and cutting tooth process of the gear were curried out. the cutter ' s tooth shape, the processed gear blank shape and its conjugated tooth profile shape as well as visual movement relationship between generating gear and processed gear blank etc. were obtained. the relative position of cutter and processed gear as well as the movement trace and rule in the cutting process can be showed dynamically on screen
在實體建模程序中，以雙圓弧弧齒錐齒輪的加工原理為基礎，藉助繪圖軟體autocad ，模擬了雙圓弧弧齒錐齒輪銑刀盤刀齒形狀、輪齒毛坯形狀等，進而根據產形輪與被加工齒坯之間的共軛嚙合關系，進行了雙圓弧弧齒錐齒輪的實體建模及加工過程模擬，在屏幕上動態顯示刀具及被加工齒輪的相對位置及其加工時的運動軌跡和規律。Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically
精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。In this dissertation, first, based on the theory of w - n gearing, characteristic of tooth profile as well as the processing principle of helical bevel gear, a cutting meshing analysis about double circular arc profile bevel gear was carried out, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of double circular arc profile bevel gear were obtained
本論文首先根據雙圓弧齒輪傳動的嚙合理論，結合其齒形特點和弧齒錐齒輪的加工原理，進行了雙圓弧弧齒錐齒輪的切齒嚙合分析，得到了切齒嚙合過程中的嚙合方程、產形輪齒面方程以及雙圓弧弧齒錐齒輪的通用齒面方程，為下一步生成雙圓弧弧齒錐齒輪的三維模型打下了基礎。After synthetically studying the effects of loading positions, rim thickness, circular pinion numbers and fillet radii of gear hob on root section stresses, a judging formula of plane stress and plane strain is proposed and verified, then 2d and 3d fem models are accurately established
系統探討了加載位置、輪緣厚度、周向齒數的確定方法，分析了滾刀頂部圓角對齒根應力的影響，提出了兩類平面問題的判據並予以驗證。分享友人