齒頂角 的英文怎麼說
中文拼音 [chǐdǐngjiǎo]
齒頂角
英文
addendum angletip angle-
Leaves papery, oval in outline, 6 - 7cm long and 8 - 11 cm wide, base rounded or subtruncate, trilobed or sometimes 5 - lobed ; lobes triangular - ovate, rarely ovate - oblong, apex acute or acuminate, margin serrulate, with appressed acute teeth, sometimes entire near base, glabrous or with tufted hairs at vein axils abaxially ; petiole 2 - 3 cm long, glabrous
葉紙質,輪廓闊卵形,長6 - 7厘米,寬8 - 11厘米,基部圓或近截平, 3裂或有時5裂,裂片三角狀卵形,有時卵狀長圓形,頂端漸尖,邊緣有疏而銳利地鋸齒,有時近基部全緣,兩面無毛或下面脈腋有簇毛;葉柄長2 - 3厘米,無毛。Witch has worked out the tooth shape of datum rack and computer simulation of gear manufacture. pointedness, undercut and tooth tip becoming sharp are analysed. tooth thickness calculation and measurement, superposition coefficient calculation and belt length calculation are resolved
2 、給出了基準齒條的齒廓形狀,進行了齒輪加工計算機模擬,分析了可能出現的稜角問題,進行了齒輪內齒頂圓的求解、根切問題分析、齒厚計算與測量、齒頂變尖的分析、重合度的計算、帶長度的計算及齒輪設計的程序編制等。Top slope angle
刀齒頂刃傾角Hot rolled steel equal flange tees with radiused root and toes - dimensions and tolerances on shape and dimensions
帶圓角齒根和齒頂的熱軋鋼等邊二層交錯凸緣.尺寸和形狀及尺寸公差The acceptability our rejection and the depiction of some content in the course " mechanisms and machine theory " is discussed, ( e. g., group dividing, solving steps of the graphical method for vector equation, versions and methods for analytical kinematic analysis, inversion design for linkage mechanisms, crank angle between the two limiting positions, design formulae for cam mechanisms, classification of combined mechanisms, formula of the radius of addendum circle of gear, balancing of machinery, etc. ) and some new opinions are presented
摘要就《機械原理》課程的某些內容(如:拆桿組的方法、矢量方程圖解法的解題步驟、運動分析解析法的版本和方法、連桿機構的反轉法設計、極位夾角、凸輪機構設計公式、組合機構的分類、齒輪齒頂圓半徑公式、機械的平衡等)的取捨和敘述進行探討,提出一些新的看法。Rake angle and senitopping can be made. it is a high effcient cutting tools
並可做成正前角或半切頂是一種高效的齒輪工具Soundboard ribs are of spruce and are fully let - in to a notched liner ( uprights ) and the rim ( grands ) to support the soundboard crown and prevent the piano from losing its tone
音板肋木也由雲杉製成,完全嵌入鋸齒狀襯墊(直身鋼琴)或琴身(三角鋼琴) ,用以支撐音板的冠狀頂部和穩定鋼琴音質。For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
研究加工不等齒厚的非標準參數漸開線齒形,與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法,介紹用限制區域選擇插齒刀變位系數的新方法,並給出刀具齒頂后角與側螺旋角的關系曲線,為插齒刀參數的選擇提供依據.結果表明,採用上述方法設計非標準復合齒輪插齒刀,可簡化計算和提高設計效率After synthetically studying the effects of loading positions, rim thickness, circular pinion numbers and fillet radii of gear hob on root section stresses, a judging formula of plane stress and plane strain is proposed and verified, then 2d and 3d fem models are accurately established
系統探討了加載位置、輪緣厚度、周向齒數的確定方法,分析了滾刀頂部圓角對齒根應力的影響,提出了兩類平面問題的判據並予以驗證。分享友人