齒頂 的英文怎麼說

中文拼音 [chǐdǐng]
齒頂 英文
crest of thread; crown of a tooth; tooth crest; tooth point; tooth-tip; tooth top; addendum齒頂間隙 （gear） tip clearance; top clearance of tooth; 齒頂角 addendum angle （傘齒輪的）; 齒頂嚙合 [機械工程] addendum peak contact; 齒頂線 addendum line; face line of teeth; top line （of teeth）; 齒頂圓 addendum [outside; point] circle
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 頂 : i 名詞（人體或物體的最上部） crown; peak; top Ⅱ動詞1 （用頭支承） carry on the head 2 （從下面拱...
  1. Characteristics : perennial pubescent herb ; leaves dimorphic, the radical with 3 - lobes, coarsely serrate at margin ; cymes terminal ; flowers yellow, to 2 cm diam., sepals 5, petals 5 or more ; fruit consisting of many aggregated achenes

    形態：多年生草本，被毛；葉兩形，基生葉3裂，粗鋸齒緣；聚傘花序頂生；花黃色，直徑可達2公分，花萼5片，花瓣5片或更多；頭狀聚合瘦果球形。
  2. Leaves papery, oval in outline, 6 - 7cm long and 8 - 11 cm wide, base rounded or subtruncate, trilobed or sometimes 5 - lobed ; lobes triangular - ovate, rarely ovate - oblong, apex acute or acuminate, margin serrulate, with appressed acute teeth, sometimes entire near base, glabrous or with tufted hairs at vein axils abaxially ; petiole 2 - 3 cm long, glabrous

    葉紙質，輪廓闊卵形，長6 - 7厘米，寬8 - 11厘米，基部圓或近截平， 3裂或有時5裂，裂片三角狀卵形，有時卵狀長圓形，頂端漸尖，邊緣有疏而銳利地鋸齒，有時近基部全緣，兩面無毛或下面脈腋有簇毛；葉柄長2 - 3厘米，無毛。
  3. Addendum modification of external spur and helical gears

    外嚙合圓柱齒輪和斜齒輪的齒頂高修正
  4. Witch has worked out the tooth shape of datum rack and computer simulation of gear manufacture. pointedness, undercut and tooth tip becoming sharp are analysed. tooth thickness calculation and measurement, superposition coefficient calculation and belt length calculation are resolved

    2 、給出了基準齒條的齒廓形狀，進行了齒輪加工計算機模擬，分析了可能出現的稜角問題，進行了齒輪內齒頂圓的求解、根切問題分析、齒厚計算與測量、齒頂變尖的分析、重合度的計算、帶長度的計算及齒輪設計的程序編制等。
  5. Black crested thread

    黑齒頂螺紋
  6. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  7. Measurement and instrument of addendum circle and dedendum circle diameter of odd tooth gears

    奇數齒齒輪齒頂圓與齒根圓直徑的測量及其量具
  8. Addendum modification of straight spur gears in the 05 - system ; introduction

    -系統的直齒正齒輪的齒頂高修正.導言
  9. The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate

    結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。
  10. Mean measuring addendum

    中點測量齒頂高
  11. Equal addendum teeth

    等齒頂高齒
  12. Addendum modification coefficient

    齒頂修正系數
  13. Face cone element

    齒頂圓錐母線
  14. Top slope angle

    刀齒頂刃傾角
  15. Hot rolled steel equal flange tees with radiused root and toes - dimensions and tolerances on shape and dimensions

    帶圓角齒根和齒頂的熱軋鋼等邊二層交錯凸緣.尺寸和形狀及尺寸公差
  16. The acceptability our rejection and the depiction of some content in the course " mechanisms and machine theory " is discussed, ( e. g., group dividing, solving steps of the graphical method for vector equation, versions and methods for analytical kinematic analysis, inversion design for linkage mechanisms, crank angle between the two limiting positions, design formulae for cam mechanisms, classification of combined mechanisms, formula of the radius of addendum circle of gear, balancing of machinery, etc. ) and some new opinions are presented

    摘要就《機械原理》課程的某些內容（如：拆桿組的方法、矢量方程圖解法的解題步驟、運動分析解析法的版本和方法、連桿機構的反轉法設計、極位夾角、凸輪機構設計公式、組合機構的分類、齒輪齒頂圓半徑公式、機械的平衡等）的取捨和敘述進行探討，提出一些新的看法。
  17. Geometrical design of cylindrical internal involute gear pairs ; diagrams for the determination of addendum modification coefficients

    漸開線嚙合圓柱內齒輪副的幾何設計:齒頂高變位系數測
  18. After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125

    以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。
  19. For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. the cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented. and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters. to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design

    研究加工不等齒厚的非標準參數漸開線齒形，與非漸開線齒形復合的鎖閉齒輪插齒刀刀齒的排列、刀具齒數的選擇以及刀具設計的基本方法，介紹用限制區域選擇插齒刀變位系數的新方法，並給出刀具齒頂后角與側螺旋角的關系曲線，為插齒刀參數的選擇提供依據.結果表明，採用上述方法設計非標準復合齒輪插齒刀，可簡化計算和提高設計效率
  20. Abstract : this paper takes the manufacturing of non - circular gear as an example to analyze the non - circular gear ' s tip curve error influence upon it s contact ratio which is manufactured by involute cylindrical shape cutter, and it provides a theory basis to control strictly non - circular gear ' s contact ratio

    文摘:以非圓齒輪插齒加工為例，分析了利用漸開線圓柱插齒刀加工非圓齒輪時齒頂曲線誤差對非圓齒輪重合度的影響，為嚴格控制非圓齒輪副的重合度提供了理論保證。
分享友人
分享到 Line

分享到臉書