adjusting screw 中文意思是什麼

adjusting screw 解釋
第螺釘
  • adjusting : 調節；調整；調準
  • screw : n 1 螺旋；螺釘。2 螺旋槳；暗輪。3 暗輪輪船。4 螺旋狀物。5 拔塞器；螺絲鉆子。6 螺旋的一擰；螺旋的...
  1. The high step moves from under the adjusting screw.

    高點從調節螺釘下移動。
  2. The adjusting screw rests on the high step of the cam.

    調節螺釘落在凸輪高點上。
  3. To readjust - loosen lock nut on the adjusting screw

    重新調節：松開調節螺絲上的鎖定螺母。
  4. Adjusting floor installation by adjusting any one of the four screw eyes must loosen the screws and adjust the below bracket

    地板安裝調節時必須將地板四角小螺絲擰下后在下部支架上進行調節
  5. The adjusting of screw prevents the throttle valve from moving to the fully closed position.

    調節螺釘防止節氣門運動到全關閉位置。
  6. Controlling temperature using scr system, the range of temperature difference controlling one centigrade, precisely controlling the thickness of sheet and flatness for the plasticizing process. adjusting the interspace of screw and pressing roll to adjust the sheet thickness, can control precisely the thickness. can select the grain roller from

    ，對塑化過程及板片厚薄平整度均能作到精確控制板片厚薄採用機筒螺桿與壓輥雙向調整，可精確控制其厚薄壓花輥從
  7. Three types of adjustable turning rolls : manual lead screw adjusting, manual bolt shifting and electric sliding plate shifting

    可調式滾輪架有手動絲桿可調式、手動螺栓移位式和電動滑板移位式三種。
  8. It has the advanced radial technology and the movement path likes 11 pieces plum blossoms shape, this machine uses a head screw pole to go up and down to control the power head, it has the enlarged bench, and air current double - direction adjusting valve to controlled the riveting speed effectively. the electricity system added the counter to count the work piece which was be processed, he time relay control the riveting times

    Jm3tq - d是汽動類小型徑向鉚接機，與jm3tq - b和jm3tq - c相比，提高最大工作行程到40mm ，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機採用頭部絲桿升降粗調，加大了工作臺面，氣路加裝雙向調節閥，有效控制鉚接速度。
  9. Feed throw - out screw : whether in embroidering or plan sewing, the fabric feed can be regulated to sew fabrics of different thickness by simply adjusting the feed throw out screw

    針距選擇及倒縫：調節針距，只用轉松固定螺釘，發動指示桿，即可縫紉不同疏密的針距或倒縫。
  10. Stitch regulation and reverse stitching : simply by turning the stitch regulator thumb screw and adjusting feed reversing handle, you can easily sew stitches of desired length or reverse stitshing

    針距選擇及倒縫：調節針距，只用轉松固定螺釘，發動指示桿，即可縫紉不同疏密的針距或倒縫。
  11. By adjusting the fuel rectifying screw and then increasing the fuel quantity per cycle, the loss of the maximum power of e30 engine ca n ' t exceed 10 % of the maximum power of diesel, and the loss of the maximum torque can be controlled within 2 percent

    通過旋出油量校正螺釘，增大燃料供給量，可以使e30混合燃料發動機的最大功率損失控制在10以內，最大轉矩損失控制在2以內。
  12. This machine is a kind of radial riveting machine, the machine adopted the advanced radial technology, and its movement path likes the 11 pieces of plum blossom s shape, and using the screw pole to ascend and descend the work bench the head part is fixed, and the t - slot of bench can fix the clamping apparatus available, the center hole of bench and axis are coaxial, the one - way adjusting valve of liquid current is effectively controlled riveting speed

    Jm12 - c是液壓類中重型徑向鉚接機，除應用有第五代徑向鉚接技術外，該機加長了鉚接行程，該項參數由普通機型的30mm加至60mm ，可滿足長行程深孔內鉚釘鉚接的要求。工作臺，並具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。氣路加裝雙向調節閥，有效控制鉚接速度。
  13. Abstract : throngh improving ram adjusting screw structure, impel it staunch and stand economic benefits raises notable

    文摘:通過對滑枕調整絲杠結構的改進，使之堅固耐用，經濟效益得到明顯提高。
  14. Adjusting rings with screw

    帶螺釘的調節環
  15. Remove compression from spring by turning adjusting screw ( 1 ) counterclockwise

    通過反時針方向旋轉調節螺絲（ 1 ）從彈簧上拆卸壓縮件。
  16. To replace seat / stem module shut off supply, loosen locknut and back off adjusting screw

    要更換閥座/閥桿模塊，先關閉供應管道，松開鎖緊螺母，退出調節螺絲。
  17. To increase the reduced pressure, turn the adjusting screw clockwise - opposite to decrease the reduced pressure

    增加減少的壓力，順時針方向旋轉調節螺絲；相反則是減少減少的壓力。
  18. To replace seat disc or diaphragm loosen locknut ( 51 ) and back off adjusting screw ( 53 ), remove four bonnet screws ( 24 ) and lift off cage ( 3 ) with spring ( 729 ) and washer ( 61 )

    要更換閥座閥瓣或隔膜，則松開鎖緊螺母（ 51 ）並退出調節螺絲（ 53 ） ，拆卸四個閥蓋螺絲（ 24 ）並將帶著彈簧（ 729 ）和墊圈（ 61 ）的籠（ 3 ） 。
  19. Check and adjust ( as needed ) valve clearance to the same specifications on nos. 2, 4 and 6 exhaust and nos. 3, 5, and 6 intake valves. tighten valve adjusting screw locknut to 27 n ? m ( 20 lb - ft )

    檢查並視需要將氣門間隙調節到與2 、 4 、 6號排氣閥以及3 、 5 、 6號進氣閥相同的規格。將氣門調節螺絲防松螺母擰緊至27牛頓?米（ 20磅- ? ） 。
  20. Adjusting bolt adjusting screw

    調節螺套
分享友人
分享到 Line

分享到臉書