air spraying process 中文意思是什麼

air spraying process 解釋
空氣噴塗法
  • air : n 1 空氣，大氣。2 天空，空中。3 微風，和風。4 態度，樣子，風度，氣派；〈pl 〉高傲的架子。5 傳播，...
  • spraying : 金屬噴鍍
  • process : n 1 進行，經過；過程，歷程；作用。 2 處置，方法，步驟；加工處理，工藝程序，工序；製作法。3 【攝影...
  1. The condensed water separated from the air - conditioning system of an airplane is sprayed in the cold side of the radiator, and the heat transfer and the state change of water in the process of its spraying to the ram air are analyzed

    摘要將飛機空調系統中水分離器分離出的游離水噴到散熱器的冷邊，並對水噴到沖壓空氣中的狀態變化過程和傳熱過程進行分析和計算。
  2. Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors

    諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3
  3. High - pressure blasts of compressed air then turned the brain into a slurry that squirted out through the same hole in the skull, often spraying brain tissue around and splattering the hose operator in the process

    然後，由壓縮空氣形成的高壓氣浪會將豬腦吹成腦漿，並同樣從枕大孔處噴濺出來? ?從事這個操作程序的時候，豬腦通常會四處噴濺，並濺射到操作者的身上。
  4. 3the spraying technique has strict process requirement on interior decorative materials. under specific circumstance, ethoxyline or polyester, via their thermosetting property, is converted into modified epoxy i. e. high molecular material so as to obtain the advantages such as smooth surface, uv resistance and air pollution resistance

    3噴塗技術對室內外裝飾材料的工藝要求極高，環氧樹脂或聚酯通過熱固性使其環氧樹脂或聚酯能在特定的條件下得到充分的反應，轉化成改性環氧即為高分子材料達到表面平滑抗紫外線，抗空氣污染等特點。
分享友人
分享到 Line

分享到臉書