analyzing rod 中文意思是什麼
analyzing rod
解釋
分析桿, 測定桿-
Based on analyzing the disadvantage of gripping device connecting technology between anode rod and bus to the roasting of aluminum reduction cells, the new method of flexible connecting device between anode rod and bus is proposed
摘要文章在分析導桿與母線夾具夾緊連接方法對鋁電解槽焙燒的不利影響的基礎上，提出了軟聯接新方法。 -
This paper, on the basis of analyzing accurately guiding drilling rod receiving strength state, stresses are calculated, has put forward the computing technology of project
本文在正確分析了導向鉆進中鉆桿的受力狀態的基礎上，進行了鉆桿應力計算，提出了工程計算方法。 -
When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。 -
The reason of defects and danger to producing and drawing of rod also were analyzed in order to provide reference for producing and analyzing quality of high carbon steel rod
分析了這些組織缺陷產生的原因以及它們對盤條生產和后續拉拔的危害，為高碳鋼盤條的生產及產品質量分析提供參考。 -
The results of analyzing new rod baffle and comparing it with the ordinary grid baffle show that the new structure has stronger restriction against the tube bundles vibration
對改進后的折流柵的剛度和管子振動固有頻率進行了分析與對比，表明改進后的折流柵抗管子振動性能更好。 -
Through the research on the loop controlling system of high speed rod mill, wuhan iron & steel company and analyzing the state of the big fluctuation of the loop and difficulty in control., this paper simulated the control system, via the system, consummating the factor that influence the loop, optimized the primary control system and find out the best curve and control parameter. finally, increase rate of eligible products for the sake of achieving the high economic benefits
對其活套套量波動大，不易控制的狀態進行分析，模擬模擬出控制系統;並在其控制系統中分析影響活套的因素，優化控制系統，找出活套控制的最優化曲線和控制參數，從而提高產品的成材率，提高產品生產的綜合經濟效益。 -
Using the optimization control method of the moderm control theories, the time - varying control and output - feedback control the authors study the variable structure active control over the rotor vibration with sma, especially the method of restraining the transient response of the rotor vibration. they get the rule of the optimum control force and the optimum control electric current and discuss the influence of variable stiffness on the total system stiffness through analyzing the structure of sma controller. they also indicate the shortcoming of the orthodox design method of a controller, especially the imbalance phenomenon caused by the lack of the rod stability, and propose a new method for improvement and items which ought to be paid attention to in the design stage
運用現代控制理論中的最優控制方法，引入時變控制和輸出反饋控制，研究利用形狀記憶合金對轉子振動進行變結構主動控制，特別是抑制轉子振動的瞬態響應的方法，得出了最優控制力和控制電流的強度變化規律；通過分析形狀記憶合金動作器的結構，探討了變剛度支承對系統總體剛度的影響，指出了傳統設計方法的不足之處，特別是由壓桿穩定性不足引起的失穩現象，並提出了改進的方法和在設計中值得注意的問題 -
By analyzing a monofilament cable, it is presented the conclusions that the influencing factors of the load - carrying properties of flexible supporting s stem include the initial prestress the diameter of tension rod or cable, the rise ratio and the height of the structure etc
通過對單根拉索結構的力學分析，提出影響這種結構剛度和承載性能的因素主要包括：初始施加預應力的大小、拉桿（索）的直徑、結構的腹高比以及結構的高度等。
分享友人