arc thickness 中文意思是什麼
arc thickness
解釋
弧線厚度-
Methods ： fifty paired embalmed cadaveric humeri ( twenty - five pairs : fourteen from male donors and eleven from female donors ) were scanned in medial - lateral ( ml ) and anterior - posterior ( ap ) position according to the humeral retroversion by ct. images of the humeri in the transverse planes at the lowest border of neck ( lbn ), 20mm and 40mm distal of lbn ( lbn - 20 、 lbn - 40 ), isthmus, head - neck anterior - posterior ( hn - ap ) were obtained. sixty - one extracortical and intracortical parameters were measured exactly by image analytic computer software that included offset, head position, head - shaft angle, head to tuberosity height ( ht ), head thickness, curvature radius, articular surface arc ( sa ), neck diameter, isthmus position, proximal and distal border of isthmus, maximum coronal and sagittal diameter of medullary canal and thickness of cortical bone in four planes, including lbn, lbn - 20, lbn - 40 and isthmus
方法： 50根成對防腐肱骨（男14對，女11對）按肱骨頭扭轉角置於冠狀位和矢狀位，行肱骨全長，頭頸矢狀面，解剖頸下緣及其下20mm 、 40mm ，髓腔狹窄部四平面ct掃描，由ct軟體測量冠、矢狀位髓腔內外參數共61項，包括頭心?干軸距，頭位置，頭干角，頭?結節高度差，頭厚度，頭半徑，關節面張角，解剖頸直徑，髓腔狹窄部位置，解剖頸下緣及其下20mm 、 40mm和狹窄部四個平面髓腔的最大冠、矢狀徑，皮質骨厚度等。 -
Steel casting : 20 tons arc - furnace steelmaking, 40tlf refiner furnace ; the max elevating capacity 125t ; the max casting products 80t, dimension of casting products length, width, high 8. 54. 53m, spun casting min outer diameter, min wall thickness, max length 1000154000mm ; various specification steel strands
鑄鋼: 20t電弧煉鋼爐40tlf精煉爐最大起重能力125t最大鑄鋼件80t鑄鋼件最大尺寸長寬高8 . 54 . 53m離心澆注最大外徑最小壁厚最大長度1000154000mm各種規格連鑄坯。 -
Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel
可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。 -
Suitable for welding of pulse mig / dc mag / co2 / flux - core wire / electric arc welding, and for welding of aluminum / titanium / copper alloys, low carbon steel, low alloy steel and stainless steel, as well as thin plate and medium thickness plate
可用脈沖mig /直流mag / co2 /藥芯焊絲/電弧焊等，分別對鋁、鈦、銅等有色金屬及其合金、低碳鋼、低合金鋼、不銹鋼等等多種材料進行高性能焊接以及薄板高速焊接和中厚板粗絲大電流高效焊等 -
The calculation results show that the stress distributing of the plug drawing tube is different because of different dies, the drawing force and pulling force are lager in arc die and the diameter and wall thickness are closer to the designing value in cone die
計算結果表明，不同的模具，芯拔管的應力分佈不同，弧形模成型的拔制力與芯棒后拉力較大，錐形模成型后鋼管的直徑與壁厚更接近設計值。 -
Effects of process parameters on thickness and hardness of micro - arc oxidation aluminum oxide ceramic coating
鋁合金微弧氧化陶瓷膜性能及其影響因素探討 -
With micro - arc oxidation, a ceramic oxidizing layer with the fare thickness and the high density is formed on aluminum alloys
摘要根據大量的實驗結果總結了微弧氧化過程中的一些規律。 -
Analysis and research were made for relation about max external pressure resisting capacity under condition of different ratio between straight section length and end arc radius on the flatted tubes with same circumference and tube wall thickness by using analytical technology of finite element
摘要應用有限元分析方法，對相同周長、相同璧厚的扁管在直邊段和圓弧半徑的不同比值條件下與所能承受最大外壓力的關系進行了分析。
分享友人