arc-control device 中文意思是什麼

arc-control device 解釋
電弧控制器件
  • arc : A. R. C. ＝ American Red Cross 美國紅十字會。n. 1. 弧；弓形，拱（洞）。2. 電弧，弧光。
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  • device : n. 1. 設計，計劃；方法，手段。2. 〈pl. 〉意志，慾望。3. 謀略，策略，詭計。4. 器具，器械，設備，裝置。5. 圖案，圖樣；花樣；紋章；標記，商標；（紋章上的）題銘。
  1. Based on researching the function of every kind of eliminating arc loop, new concept was brought up in this paper, and the protective device for eliminating arc and overvoltage was researched and manufactured. when the arc light connecting the ground emerges, the chip synthesizing controller control the vacuum contacter which can be operated with dividing phase and make its fault phase earthed so that the arc light can be dissolved thoroughly

    本文在研究各種消弧線圈的基礎上，提出全新的概念，研製出了消弧及過電壓保護裝置，該裝置在出現弧光接地時，通過單片機綜合控制器控制一組可以分相操作的真空接觸器，使故障相接地，達到徹底消除弧光的目的。
  2. Especially the base machine require the precision of transmission of the device to expect very much to it, and its control is more difficulty of heavy degree systematically in succession than arc casting, so resulted in the popularity and application of technology in succession of horizontal continous casting getting influence

    尤其是拉坯機對其驅動裝置的傳動精度要求很高，其控制比弧形連鑄系統難度大，致使水平連鑄技術的推廣應用受到影響。
  3. The function of the software use pc - computer to dispose the output signal which is produced by the device as following steps : ( 1 ) to input data by parallel interface ( 2 ) to record and form a file ( 3 ) to demonstrate results step by step ( 4 ) the results could be compiled ( 5 ) it can synthesis in the permitted error scope, substituted original dot for line or arc, finally we could get a graph that is described by some simply curve. ( 6 ) to convert these graph into a program, which used in the cutting process of numerical control. ( 7 ) the software also includes some protective methods

    而系統處理軟體的作用是：利用pc兼容機，將上述裝置的輸出信號（ 1 ）通過并行口輸入（ 2 ）記錄成文件（ 3 ）逐點顯示出來（ 4 ）可人工進行化簡，編輯（刪、改點）等（ 5 ）可在給定誤差范圍內進行人工擬合，用直線和圓弧取代原來的點，得到一個與原圖形的誤差在規定范圍內，又消除跟蹤過程中因受到各種干擾而造成的缺陷，由盡可能少而簡捷的數學曲線描述的圖形（ 6 ）把這些圖形轉化成用於編制數控線切割加工程序及autocad能夠識別的文件（主要指dxf格式） （ 7 ）該軟體還有一定的加密措施。
  4. A novel current control mode pulse width modulation switched high frequency resonant arc igniting device is developed based on uc3842 and the principle is analyzed

    摘要採用uc3842設計了電流控制型脈寬調制開關式高頻振蕩引弧器，並對其工作原理進行了分析。
  5. The welding position can be detected accurately through processing the image of arc area collected by the vision sensor ccd ( charge coupled device ), by the system of image collection and computer - ware, we can recognize the position of the welding line exactly, count out the warp between moving track of robot and the welding line. so we can control the robot ' s act real - timely, the seam tracking accuracy is enhanced efficiently

    重點論述焊縫圖像分割和邊緣提取的理論方法，焊縫圖像由面陣ccd攝像系統攝取，通過圖像採集系統和計算機軟體，對檢測到的弧焊區圖像進行處理來準確地識別焊縫位置，計算機器人的運動軌跡和實際焊縫之間的偏差，據此控制機器人運動進行實時跟蹤，從而有效地提高焊縫跟蹤精度。
  6. Vibration - resisting electricity contact pressure meter is used for occasion by environment quake vibration excle in pulsaling lash by medium - resistant and suddenly unload ; usually it is make use of form a complete set by relevant eletric device ( such as relay and contact appliance and so on ). so realized attain auto - control post a letter ( give an alarm ) for pressure system by survey. compare with ordinary for a special model electricity contact pressure meter, zhe indicator ' s function by survey pressure more stabilize, more accurate, and powerful of resist eletric arc, and it is use for even more long life

    耐振電接點壓力表，適用於環境劇烈振動場合，可耐介質的高強脈動沖擊及突然卸荷；通常該儀表經與相應的電氣器件（如繼電器及接觸器等）配套使用，即可對被測（控）壓力系統實現自動控制發信（報警）的目的，與普通專用型電接點壓力表相比，指針測壓性能更穩、準，且抗電弧強大，使用壽命更長。
  7. Selection modse of long / short weld, build - in remote control device, capable of ignition and cratering electric arc with small current

    具有「長焊縫/短焊縫」選擇功能及遙控裝置，可進行小電流引弧，收弧。
  8. This machine adopts high - level siemens plc concentration control, set up with computer controlled gear shifting vacuum gauge, and a three - flow controller, one set of contra - variant bias power and four - route contra - variant arc power supply, four side - installed heating tubes, computer pid automatic temperature control device, 60 and 100 two kinds versatile arc supply

    該設備採用先進的西門子plc集中控制，裝有電腦自動換檔真空計和三路流量控制器，一套逆變偏壓和四路逆變弧電源，邊裝式加熱管四支，電腦pid自動控溫， 60和100兩種弧源通用。
分享友人
分享到 Line

分享到臉書