axial thrust load 中文意思是什麼

axial thrust load 解釋
軸向分力
  • axial : adj. 1. 軸的。2. 成軸的。3. 軸周圍的，軸向的。adv. -ly 在軸的方向，與軸平行地。
  • thrust : vt （thrust）1 猛推，沖；猛撳，沖入，插入，推入（出），突出，伸出，塞，刺，戳，戳穿。2 逼迫，把[...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  1. Radial - thrust floating - ring hybrid bearing, which can not only sustain the radial load but also the axial load, colligate the strongpoints of pure dynamic and static bearings

    徑?推聯合浮環動靜壓軸承自二十世紀七十年代經提出后，已進行了較為系統的研究。
  2. In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members

    三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。
  3. In chapter 5, using coordinate graphs, the influences of rectangular screw, trapezoidal screw and serrate screw on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are compared and analyzed

    第五章，通過坐標圖對比分析了微型機器人在矩形螺紋、梯形螺紋、鋸齒形螺紋下，各螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。
  4. In chapter 2, an accurate modified reynolds equation is derived. the modified reynolds equation is solved numerically with the finite different method, the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction under the rectangular screw are obtained. at last, using numeral methods and coordinate graphs, the influences of rectangular screw parameters on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are studied and analyzed

    第二章，首先推導了非牛頓流體的變形雷諾方程，化簡了雷諾方程，得出了矩形螺紋下有限差分方程；還推出了矩形螺紋作用下軸向摩擦牽引力、粘液膜厚度、粘液膜承載能力、周向摩擦阻力無量綱表達式，最後用數值計算方法求解，通過坐標圖分析了矩形螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。
  5. In chapter 4, the modified reynolds equation is solved numerically with the finite different method, and the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction under the serrate screw are obtained. at last, using numeral methods and coordinate graphs, the influences of serrate screw parameters on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are studied and analyzed

    第四章，首先求出鋸齒形螺紋下數值計算所需的有限差分方程，再推出了鋸齒形螺紋作用下軸向摩擦牽引力、粘液膜厚度、粘液膜承載能力、周向摩擦阻力無量綱表達式，最後用數值計算方法求解，通過坐標圖分析了鋸齒形螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。
  6. Axial thrust load

    軸向推力負荷
  7. In chapter 3, the modified reynolds equation is solved numerically with the finite different method, and the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction under the trapezoidal screw are obtained. at last, using numeral methods and coordinate graphs, the influences of trapezoidal screw parameters on the generated axial thrust force, minimal mucus film thickness, load capacity of hydrodynamic pressure and circumferential friction are studied and analyzed

    第三章，首先求出梯形螺紋下有限差分方程，然後推導了梯形螺紋作用下軸向摩擦牽引力、粘液膜厚度、粘液膜承載能力、周向摩擦阻力無量綱表達式，並用數值計算方法求解，通過坐標圖分析了梯形螺紋參數對軸向摩擦牽引力、最小粘液膜厚度、粘液膜承載能力、周向摩擦阻力的影響。
分享友人
分享到 Line

分享到臉書