balanced amplifier 中文意思是什麼
balanced amplifier
解釋
對稱放大器-
Balanced electrometer amplifier
平衡式電測放大器 -
The use of balanced transmission lines can help but if the signal bandwidth extends to dc there will be a need for a very high performance instrumentation amplifier at the receiving end to restore a ground referenced signal
採用平衡傳輸線有助於改善信號完整性，但是對于帶寬延伸到dc的信號，接收端要靠超高性能的儀表放大器來還原參考電平。 -
Balanced valve amplifier
電子管推挽放大器 -
Become a kind of new electronics circuit - current - mode circuit. it is replacing the traditional design method of the voltage - mode in the high frequency high - speed signal processing realm 。 this thesis mainly discussed the modified second - generation current conveyors based on the current - mode kinds of new cuicuit components, they are stronger modified standard current - mode parts in fuctions on this foundation. mainly including the modified differential difference current conveyor ( mddccii ) 、 the fully balanced second generation current conveyor ( fbccii ) 、 ( full balances ) four - terminal floating nullor ( fbftfn ) and the current differencing buffered amplifier ( cdba ), they are all function very strong standard current - mode parts, they all can provide some circuit functions of better than general operation amplifier, because they have the voltage importation and the current importation, therefore use it since can carry out the voltage - mode signal processing circuit expediently, can also carry out the current - mode signal processing circuit expediently, and have to increase the benefit bandwidth to accumulate more widely than the voltage - mode, but have their advantages more according to the current - mode filter of the modified current conveyor, because it constitutes in brief, the filter wave function is stronger and they are better than in general use operation amplifier of many advantages, be easy to composing for example 、 high speed 、 frequency bandwidth 、 the power supply voltage requests low 、 consume small, the impedance is different from etc. advantages, otherwise they have biggish dynamic range, and flexible circuit synthesize, so they are the best active parts
從第二代電流傳輸器ccii入手，重點研究了以下幾種改進型的第二代電流傳輸器:改進的差動差分電流傳輸器mddccii 、全平衡第二代電流傳輸器fbccii 、多輸出四端浮地零器ftfn 、全平衡四端浮地零器fbftfn 、電流差分緩沖放大器cdba的電路結構及其模型。然後在此基礎上系統地研究了基於這幾種改進型的第二代電流傳輸器的濾波器的設計方法，主要方法和結果如下:利用mddccii設計了差分式連續時間電流模式低通、帶通濾波器;電流模式跳耦結構考爾低通濾波器;利用fbccii設計了帶通二階節濾波器及電流模式雙二階通用濾波器;設計了基於多輸出端ftfn的電流模式二階通用濾波器電路;通過數字化開關選擇的基於fbftfn的電流模式通用濾波器;設計了基於最少個數電流緩沖放大器（兩個cdba ）的多功能通用電流模式濾波器及其在非理想因素情況下分析。設計濾波器的主要方法是採用級聯設計、運算模擬（信號流圖法）和反饋設計（跳耦法） 。 -
First, an analysis for the design of the impulse phase lock oscillate, which includes impulse phase detector the dielectric resonant oscillate etc. secondly, presents an analysis for the design of wide band balanced low noise amplifier. the last two part simplify the theory and the electrical characteristics of the sub harmonic mixer, and the mmvco
第一部分著重介紹了脈沖鎖相源的工作原理（主要包括取樣鑒相器和介質穩頻的壓控振蕩器） ，並介紹了研製結果的性能指標;第二部分介紹了平衡式寬帶低噪聲放大器的基本理論 -
Bridge balanced amplifier
橋式平衡放大器 -
Broadband matching is very difficult, but we can make it easier with negative feedback and balanced amplifier. so at first we should choose a project, then according to the requirement of the low noise amplifier to choose the transistor, bias and matching
寬帶匹配網路的設計是一個難點，可以採用負反饋、平衡電路等形式降低寬帶匹配的難度，所以寬帶電路的設計首先是方案設計。 -
In the sixth chapter a low noise amplifier whose operating frequency is 6ghz 12ghz is presented. it is a balanced amplifier. in this chapter we discuss the calculation of lange coupler, the matching of balanced amplifier and the influence of thin film mic in the design
第六章設計的6ghz 12ghz的低噪聲放大器為平衡放大器，詳細討論了蘭格耦合器的計算、平衡放大器中匹配電路的設計和薄膜mic工藝對電路設計的影響。 -
The theory and design of the balanced converter, fin - line waveguide bandpass filter, waveguide to microstrip transition and millimeter - wave amplifier are studied in this paper. finally the paper presents the structure and the simulated result of each module
本文對組件中的平衡上變頻器，鰭線波導帶通濾波器，波導微帶轉換結構以及毫米波信號放大器的原理和設計進行了討論，並給出了電路結構，模擬結果。 -
In view of the importance of rf front - end circuits in the receiver system, the paper finally is focused on the analysis and design of the rf front - end circuits, including the design of low noise amplifier ( lna ), microstrip filter and balanced mixer. all the circuits above are simulated individually using ansoft serenade, and the results are satisfying with the desired performance
考慮到射頻前端電路性能的好壞會直接影響到整機的性能，文中還重點論述了該接收機射頻前端電路的分析和設計，主要包括低噪聲放大器、微帶濾波器和單平衡混頻器的理論分析和實際設計，並在ansoftserenade環境下進行了模擬模擬，模擬結果符合設計要求。
分享友人