base of tooth 中文意思是什麼
base of tooth
解釋
齒根-
The main research work in the thesis is as follows : ( 1 ) base on the analysis of cutting principle and tooth geometry characteristics of klingelnberg cycloid bevel gear, the formula of tooth design calculation was verified and the equation of imaginary crown gear tooth flank was deduced by establishing appropriate coordinate system
主要研究工作和成果有: （ 1 ）通過分析克林貝格擺線錐齒輪銑齒原理，對其部分幾何設計演算法進行了推導驗證，並建立了適當的坐標系推導了假想冠輪的齒面方程。 -
Results : 1 ) under the same condition of loading, the stress and displacement of mesial occlusal rest design was smaller than that of distal occlusal rest design in abutment teeth and soft tissue under the base, however, the magnitude in the soft tissue under base was bigger. 2 ) when a distributed vertical load was applied to the artificial tooth abutment teeth regions, the stress distribution was similar to that of concentrated load in the artifitial tooth, and stress magnitudes were higher. 3 ) under the condition tested, the mesial occlusal rest design caused the stresses that were more in line with the long axes of the abutment teeth than did the distal occlusal rest design
結果： 1 ）在同一加載條件下，近中（牙合）支托設計與遠中（牙合）支托設計相比，基牙及基托下軟組織的應力和位移值減小；基托下軟組織的應力和位移值大於基牙； 2 ）基牙及義齒整體加載時，各基牙應力分佈規律與人工牙加載相同，但應力值增大； 3 ）近中（牙合）支托設計使基牙受力更趨于軸向。 -
On the base of the basic structure study of the tooth - locked quick closure vessel of middle and low pressure with crown head, the optimization method of parameterized whole device is presented in this paper, the emphases of research is put on optimization of the tooth - locked quick closure device whose structure and load distribution is complicated, the wall of vessel, however, is designed according to the existing strength formula
本文對帶有球冠形封頭的中、低壓齒嚙式快開容器的基本結構進行研究的基礎上，提出了齒嚙式快開容器的參數化整體優化方法，研究重點放在結構和受力復雜的齒嚙式快開裝置的優化，對于容器簡體壁厚仍採用現有強度公式設計。 -
This paper investigates the vibration features of various typical gearbox faults including profile error, broken tooth, symmetrical tooth wear, serious unbalance of shaft, on the base of theoretic analyses and plenty of cases. it provides guide for further gearbox - fault - automatic - diagnosis
在理論分析和大量的工程實例基礎上，提取了包括齒型誤差、斷齒、齒輪均勻磨損、軸嚴重不平衡、箱體共振五種齒輪箱典型故障的振動特徵，為實現齒輪箱故障自動診斷提供了理論依據。 -
Establishs to 2 00 3 in this mill, although very short 1 year time, yet this mill draws lessons from well - developed administration of trade home and abroad colleague s and technique experience, devotes self to to forge the home and abroad the largesttest - abs provides against holing or carry in the arms the tooth and encircles one of production - manufacturing base
本廠創建於二00三年，雖短短一年時間，但本廠借鑒國內外同行業先進的管理及技術經驗，致力打造國內外最大abs防抱圈生產製造基地之一。 -
Start directly from the actual shape of gear tooth, taking the similarity theory as a base, and by means of sampling calculation of boundary element and analysis of three elements regression, the simplified formulae for calculation of tooth root stress were established
摘要直接從輪齒的實際形狀出發，以相似理論為基礎，通過邊界元采樣計算和三元回歸分析，建立齒根應力計算的簡化公式。 -
3. base on the numeric method of finite element, the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied. with the increase of the tooth number, tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient, tooth root maximum pull stress increase
3 、基於有限元數值計算方法，分析了不同關聯變位系數和齒數z對齒輪彎曲強度的影響：隨著齒數的增大，齒輪最大拉應力減小；關聯變位系數越大，齒輪最大拉應力越大。 -
Abstract : the measurement of asymmetric gear is discussed, especially the measurement of base tan - gent length of this kind of gear is studied in details. the formula of measuring and calculating the base tangent length and the number of tooth - jump are deduced in order to use in real production
文摘:就非對稱齒輪的測量問題進行探討，特別是公法線長度測量進行詳細研究，並推導出計算公式和跨齒數，以便於以後在生產上使用
分享友人