bed of flux 中文意思是什麼
bed of flux
解釋
焊藥墊-
The performance of catalyst beds was experimentally studied. the influence on decomposition was investigated with changing the mass flux through the cross of the catalyst bed and the initial temperature of the catalyst bed. the experimental results were compared with those of the numerical simulation
對過氧化氫催化床的催化性能進行了試驗研究，分析了催化床床載、催化床初始溫度對過氧化氫催化分解的影響，與一維情況下的數值模擬結果進行了對比。 -
Whole scheme of frame design of test - bed is proposed as : the host fanner supply the firebox the once and twice air required by diesel oil ' s burning and the cooling air ; the export parameter of the test - bed is varied by the adjust of the flux of air and diesel oil. and the air flux is varied by adjusting the rev of the fanner adjusted by transducer and the corner of the fan inlet adjusted by step motor. the quantity of oil is varied by adjusting the oil valve adjusted by step motor ; the measurement of the air flux in the test - bed adopts the method of fanner dynamics performance test in the nation criterion
確立了實驗臺結構設計方案：主風機為燃燒器提供燃燒所需的一次、二次進風量及冷卻風量；利用變頻器調節主風機轉速、用步進電機調節風門開度來調節風量，用步進電機調節回油閥開度來調節供油量，從而實現對模擬實驗臺出口煙氣熱流量的調節；實驗臺的流量測量採用風機動力性能測試標準中測流量方法等。 -
Simulation results show that based on the regeneration kinetics of the catalyst, properly raising the reoxidation temperature of the catalyst in the fluidized bed reactor either can obviously improve the performance of the system or can reduce the solid flux and hence the energy consumption
結果表明，使烴類選擇氧化（催化劑被還原）和催化劑氧化再生分開進行，特別是根據催化劑氧化再生動力學的要求，適當調節再生過程的溫度，既能明顯改善反應系統的性能，又可以大幅度降低催化劑固體顆粒的循環量，取得節能降耗的效果。 -
The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。 -
In this paper, we applied the vapor - liquid - solid three - phase circulating fluidized bed evaporator to condense glucose solution considering its advantage. in the experiment, we changed the parameters such as evaporation temperature, difference in temperature of the fluid heating and heated, liquid flux, liquid thickness and the ratio of inert particles to analyze and study this kind of equipment ' s heat transfer properties in different operational conditions
通過改變蒸發溫度、傳熱溫差、料液流量、料液濃度以及惰性粒子的體積分率等參數，研究了其在不同操作條件下的傳熱性能，並給出了汽-液-固三相循環流化床蒸發器沸騰傳熱的數學模型，模型預測值與實驗值吻合較好。
分享友人