blow test 中文意思是什麼
blow test
解釋
沖擊試驗-
Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。 -
The test result proves the blow - off point of shock absorber valve system can be identified effectively
試驗結果證明，該方法可以有效地確定減振器閥系的開閥點。 -
This paper put forward a method, which is used to identify the blow - off point of shock absorber valve system, based on the damping - displacement characteristic test of shock absorber, conversation of energy and equivalent damping coefficient
摘要以減振器示功特性試驗為基礎，以能量守恆為依據，提出一種以等效阻尼系數為對象的識別減振器閥系開閥點的方法。 -
To investigated the ignition and lean blow out performance of a trapped vortex combustor ( tvc ) test rig, abundant experiments have been employed in variety inlet conditions
摘要為了研究駐渦燃燒室拓寬燃燒邊界的能力，設計了一種駐渦燃燒室實驗件，並對其點火性能和貧油熄火特性進行了實驗研究。 -
Standard test method for environmental stress - crack resistance of blow - molded polyethylene containers
吹模製聚乙烯容器抗環境應力裂紋的標準試驗方法 -
Method for evaluation of blow formability by bulging test on metallic superplastic materials
通過對金屬超塑性材料的膨脹試驗評價吹製成型法 -
Thermoplastic tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods
吹模或旋轉模製聚乙烯熱塑性罐.地上化學制劑儲罐.要求和試驗方法 -
Thermoplastics tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods
吹模或旋轉模製聚乙烯熱塑性罐.化學製品地上存儲罐.要求和試驗方法 -
Thermoplastic tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods ; german version en 13575 : 2004
吹模或旋轉模製聚乙烯熱塑罐.地上化學制劑儲罐.要求 -
Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - blow moulded polyethylene, rotationally moulded polyethylene and polyamide 6 by anionic polymerization tanks - requirements and test methods
家用燃料油煤油和柴油的地上存儲用熱塑性固定儲油罐.通過陰離子聚合吹塑聚乙烯儲油罐旋轉模製聚乙烯和聚酰胺6儲油罐.要求和試驗方法 -
Injection molding, blow molding, technical test committee member
射出壓製成形，吹煉壓製成形，技能審定委員 -
The test train also had new interior safety measures to soften the blow to a passenger ' s body during the crash
實驗用火車也設置了新的內部安全裝置來柔緩火車碰撞時帶給乘車人身體的沖力。 -
Finally, in section three, rayleigh wave exploration method is used in a practical project - northern stone material trade market. the embedded depth of cobble substratum of the whole site, and the regression equation between the test blow count ( n63 ) standard penetration and the surface wave velocity ( vr ) are obtained in the process. a good case study is provided for the practice of the subjected method in this section
第三部分是將瑞雷波法勘探應用於北方石材交易市場的工程實際中，得到整個場地的下臥卵石層的埋藏深度，並給出該場地的標貫值n _ （ 63 . 5 ）與v _ r間的回歸方程，為這一方法的應用提供了很好的工程實例。 -
08. 02 test method for environmental stress - crack resistance of blow - molded polyethylene containers
吹模聚乙烯容器耐環境應力斷裂試驗方法 -
This was a good recovery after the engine dramas that stymied test driver anthony davidson on friday, and testament to the team thinking on its feet as they altered the way in which they ran the motors after the two blow - ups
在周五測試車手安東尼-戴維森經歷了引擎故障這是一次不錯的恢復，而且是車隊在受到兩次爆缸之後因為改變比賽方式而狀態恢復的證明。 -
Pressure relief hydrogen tester is used to test [ h ] content in aluminum liquid by vacuumizing to relieve pressure and blow up bubble, which can be mainly finished within 5 minutes
減壓測氫儀通過抽真空減壓放大氣泡的方法來測量鋁水含氫量， 5分鐘即可大致測鋁液中含氫值。
分享友人