blowing position 中文意思是什麼
blowing position
解釋
吹煉位置-
At the moment the ejection seat whipped stricklin into that optimum position, it created an exit for him, blowing the canopy off the jet fighter
就在彈射座椅把斯特里克林固定在最佳位置的那一刻，座椅還會同時把駕駛艙頂蓋炸開，從而為他留出逃生出口。 -
Results show that the influence of mainstream reynolds numbers on heat transfer coefficience is little and the heat transfer coefficience raise with the increase of reynolds numbers. the influence of the position of holes on heat transfer coefficience is complex and correlate with the mainstream speed and the balde surface curvature. and the influence of blowing ratio on heat transfer coefficience is more great ( especially to stator ), and show a complex relation to mainstream reynolds number and the position of holes
實驗結果表明，不同孔位出流的換熱由於孔排下游表面來流速度及葉片表面曲率的不同而有不同的規律，而主流雷諾數對葉片表面特別是壓力面和前緣區域的換熱系數比的影響較小，吹風比對換熱系數影響較大（特別是導葉） ，並且隨氣膜孔位置和來流雷諾數的變化而情況復雜。 -
Above all, the surface of the gas turbine blade including stator and rotor heat transfer coeficience with no film cooling hole was studied with the main stream reynolds number of 150000, 200000 50000, 300000, 350000, 400000. then, the heat transfer coefficience when all cooling holes opened and only one cooling hole opened was studied partly. and it ' s studied how the mainstream reynolds number, blowing ratio and the position of holes affect the heat transfer coefficience of the surface of blade
對導葉和動葉，都是先研究了在150000 ， 200000 ， 250000 ， 300000 ， 350000 ， 400000雷諾數下，沒有氣膜冷卻時的表面換熱系數分佈，然後研究了氣膜孔全打開和只打開單排孔時的表面換熱系數分佈曲線，重點研究來流雷諾數，吹風比和不同孔位出流對換熱系數分佈的影響規律。 -
Move the reversing handle to the ahead side and to the stop position alternately. there is proper blowing from the line filter ( 51 - 4 ) corresponding to the operation
移動換向手柄到正車側和倒車側交變地。有適當的氣從濾器51 - 4吹出相應到操作。 -
Today. getyear built in 1989, with the predominant position and convenient transportation our corporation situates in xiebian industrial zone of dali, nanhai, which is renowned as aluminum profile production base of china. as one of the earliest corporations of aluminum products, our main products are sealed transparent adhesive tapes for aluminum doors and windows, rubber tubes, blowing membrane material, domestic and imported anticollision adhesive tapes, rubber transparent anticollision adhesive tape, magnetic stripes, latent wheels of built - in cupboards and other furniture fittings of aluminium material with the brand of weijia and hengjiao
我廠創建於1989年，位於經濟發達，素有「全國鋁材生產基地」之稱的南海大瀝鎮謝邊工業區，地理位置優越，水陸交通十分方便快捷，是一家專業研製生產經營威佳牌橫?牌鋁門窗透明密封膠條膠管吹膜料國產和進口防撞膠條橡膠透明防撞膠條帶自粘透明磁條毛條自粘毛條壁櫃隱輪及鋁材傢具配件等各種產品規格全的大型企業，也是廣東地區最早開發生產此類產品的廠家之一。 -
After blowing into his mouth twice, check if the carotid pulse is present. if there is pulse but no breathing, continue to apply mouth - to - mouth ventilation at a rate of 5 seconds until the patient resumes breathing. then place him in a recovery position to provide a free airway
吹過兩口氣后，檢查其頸動脈是否跳動，如有跳動但沒有呼吸，則繼續以每五秒吹一口氣的速度進行人工呼吸，直至病者恢復呼吸為止，然後置病者于復原臥式。 -
The distribution of the mass flow rate, the heat transfer coefficients and the film effectiveness of cylindrical holes was measured. the influence of mainstream reynolds number, blowing ratio and the position of holes on flow rate, the heat transfer coefficients and the film effectiveness was studied greatly
測量了氣膜孔的流量系數、氣膜孔下游換熱系數和冷卻效率的分佈，重點研究了主流雷諾數、二次流吹風比以及孔排位置對氣膜孔的流量系數、氣膜孔下游的換熱系數和冷卻效率的影響。
分享友人