bonding power 中文意思是什麼
bonding power
解釋
成鍵能力-
Cast metal joint boxes for power cables up to 10 kv ; correlation of joint boxes with paper - insulated cables ; correlation of bare stranded copper bonding wire
最高可達10 kv電力電纜用金屬鑄造連接盒.第3部分 -
Then the key process parameters of laser bonding, including laser power, scanning velocity, and initial temperature, are obtained with the help of scanning experiments
運用該模型計算了不同的工藝參數條件下硅玻璃的溫度場分佈，並由此得出鍵合線寬。 -
Saw - blades made of iron - based matrix with different additives were fabricated to carry out the sawing of granite. the consumed spindle power, cutting forces and the wear resistance of the saw - blades were measured. sem observations on the worn surfaces of saw - blade segments were also carried out to reveal the wear characteristics of diamond grits and the metal matrix as well as the bonding at the diamond - matrix interface
製造含不同添加劑的鐵基金剛石鋸片，進行花崗石鋸切實驗，測定鋸切功率、鋸切力和鋸片的耐磨度，並用掃描電鏡觀察節塊工作面上金剛石磨粒和金屬胎體的磨損形貌及金屬胎體和金剛石界面結合狀況，綜合評價不同添加劑對鋸切性能的改性效果。 -
The plastics and board adhesive is particularly for the bonding of the pvc wood grain decorated plastic plate and the plank or the fiber board of medium density, etc since it has high adhesive strength and strong adsorption power. the adhesive can be used for the adherence of paper and plastics also
塑板膠，粘接強度大，吸附力強，不易脫膠翹邊，對pvc木紋裝飾塑片與木板中纖板等材料的復合粘貼具有獨特的粘接效果，亦可用於紙-塑粘合。 -
It finds that the radicals generated in plasma control the deposition process and the main bonding configurations of films are dependent on the ratio of cf and cf2 radicals in films. the films composed of cf2 and cc bonds can be obtained at microwave power above 560 w. the frequency dependence of dielectric constant ~ ( f 1 x 10 ~ ? x 106 liz ) ii and dielectric loss tan5 ( f = lxi 02 ? 1 x 1 o5hz ) follow a power law respectively and all show decreasing trends as frequency raised
薄膜的介電頻率關系（ f = 1 10 ~ 3 - 1 10 ~ 6hz ）和損耗頻率關系（ f = 1 10 ~ 2 - 1 10 ~ 5hz ）均服從指數規律，隨頻率的增大而減小；對薄膜的電導頻率關系的分析表明，這種指數規律的介電色散關系與由缺陷中心之間簡單隧穿引起的跳躍導電過程有關。 -
A huge actual constructions and tests has proved that the bonding power of the bonding surface is often too small to satisfy the actual stress, and that in the construction of the new to old concrete, the construction process is blind because there are no unified standards of the construction technology, which leads to the quality of the construction is inferior. and in the design process, the designers who can ’ t identify the strength of the bonding surface can not make an accurate, economic and proper design, which will lead to waste or engineering accident
大量的實際工程和試驗證明，結合面的粘結力通常比較小，往往難以滿足實際結構受力的需要，而且在新舊混凝土粘結的施工過程中，施工工藝沒有統一的標準，造成施工過程的盲目性，最終導致工程質量的低劣;在設計過程中設計人員不能判斷出粘結面的強度，這就使設計人員不能準確、經濟合理的做出設計，造成浪費或埋下工程事故的隱患。 -
Considering status of present electric power quality monitoring, an flush bonding electric power quality monitoring devise based on dsp + arm truss is proposed to satisfy the demand for supporting the real time and complicated algorithm, this equipment can accomplish the measure of electric power quality index in wind power plant, and have some other functions such as date showing, date saving and communicating etc, it make more shortcut to analyze and manage the date of power quality
根據電能質量監測對于系統支持復雜演算法和實時性的特殊要求，並在綜合分析了目前風電場電能質量監測技術現狀的基礎上，本文提出了一種基於dsp + arm構架的嵌入式電能質量監測裝置的解決方案，該裝置可完成風電場電能質量指標的測量，並有數據顯示、存儲、通信等功能，能更加快捷地對電能質量數據進行分析和處理。 -
Several methods on joining of ceramic / metal are reviewed. the joi ning of ceramic / metal brazing, partial transient liquid bonding and shs welding on power engineering and high - temperature composite of advanced jet engine, are emphasized
綜述了陶瓷與金屬連接的幾種方法，重點討論了對未來動力工程和先進發動機有重要意義的陶瓷與金屬釬焊連接、部分瞬間液相連接及自蔓延高溫合成（ shs ）連接。
分享友人