calculation specification 中文意思是什麼

calculation specification 解釋
運算說明書
  • calculation : n. 1. 計算，計演算法。2. 推定，預測。3. 深思熟慮，精打細算；慎重的計劃；算計。
  • specification : n. 1. 詳細說明，逐一登記，詳記。2. 〈pl. 〉規范，規格。3. 清單，明細單。4. 【法律】（申報新發明時的）設計說明書。5. 【法律】用來料加工製成新產品所取得的權利。
  1. In most cases, it was found that the jb criterion is safer than hg specification, but adverse result was obtained when r / r is close to 0. 8 and d / t is too small ( less than 40 ). code in c language was worked out for simplifying the calculation

    在大多數情況下，按照jb標準對此種結構進行補強設計時其安全裕度要比hg標準為高；但是當開孔率接近0 . 8且d t很小時（不大於40 ） ，依jb標準補強設計后的安全裕度反而較按hg規范計算結果要小。
  2. On the basis of this, the paper makes a great deal of calculation and analysis in this part, different parameters " effect and stress gradient are included. local buckling coefficient and the efficient width calculated formula are provided and look forward to take a reference to the redaction of the specification

    本文對此內容進行了較為深入的研究，考慮了多個參數的影響，對各種應力比作用下的楔形腹板的屈曲及屈曲后強度進行了計算分析，得出了考慮翼緣相關作用的楔形腹板屈曲系數及有效寬度系數的計算公式，以期為規范的修訂提供參考。
  3. For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels

    為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。
  4. Specification for calculation of noise disturbance effects of ac electrified railways on telecommunication lines

    交流電氣化鐵道對電信線路雜音干擾影響的計算規程
  5. Abstract : the article utilized theory of gas dynamics to research and analyze gas explosion model in boiler s chamber to investigate calculation means of explosion intensity in it, to supply technique specification for the design and manufacture of gas boiler

    文摘:應用氣體動力學理論，研究分析可燃氣體在鍋爐爐膛內爆燃模型，探索其爆燃強度的計算方法，為燃氣鍋爐本體設計和製造提供有關技術資料。
  6. Specification for calculation of protecting distance for ac high voltage overhead power transmission lines to shortwave radio direction finding stations and receiving stations

    交流高壓架空送電線對短波無線電測向臺站和收信臺站保護間距的計算規程
  7. Specification for calculation of protecting distance for ac highvoltage overhead power transmission lines to shortwave tadio direction finding stations and receiving stations

    交流高壓架空送電線對短波無線電測向臺
  8. Additionaily, the calculation method presented by specification for design of r. c. special shaped columns ( dbj / tl5 - l5 - 95 ) is discussed. in order to study the shear responses of special shaped columns, the ratio of tensile flexural steels " the ratio of moment and the shear - span ratio were analyzed

    為了研究異形截面柱的受剪性能，本文在總結已有試驗資料的基礎上，分別討論和分析了考慮受拉縱筋配筋率、彎矩比和剪跨比對異形截面柱受剪承載力的影響。
  9. Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending

    本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算，主要進行了以下四方面的研究工作： （ 1 ）輕鋼龍骨復合承載墻體的受壓、受彎計算：以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據，重點考慮罩面材料對墻龍骨設計的影響，給出了目前對承重墻龍骨設計的具體要求，並對剪力蒙皮進行了簡要討論；然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體（即罩面支撐墻龍骨）受壓、受彎的計算理論和方法；最後對提出的計算進行簡化，使之完全與我國規范相符。
  10. In this paper, the traffic surveys and analysis of typical heavy - load road were performed firstly ; also the characteristics of traffic, load and distribution of axle load were studied. the deficiencies in the calculation method of surface equivalent modulus of foundation in present specification of cement concrete pavements design for highway were analyzed. based on the elastic multi - layer theory and principles of displacement equivalence, and a great amount of computing data, a calculation method was established

    本文首先從典型重載交通道路的交通調查與分析入手，研究了重荷載交通道路的交通量、軸載分佈及荷載特徵，針對現行設計規范中關于基層頂面當量回彈模量值計算公式存在的不足，利用彈性層狀體系理論，按照彎沉等效原則，通過大量的計算分析，回歸出了精度較高、適用范圍更廣的基層頂面當量回彈模量計算公式。
  11. Specification for calculation of interference effects of ac highvoltage overhead power transmission lines on nondirectional beacons

    高壓交流架空送電線無線電干擾對中波導航影響的計算規程
  12. Specification for calculation of interference effects of ac high voltage overhead power transmission lines on non - directional beacons

    高壓交流架空送電線無線電干擾對中波導航影響的計算規程
  13. Delay and power calculation standards - pre - layout delay calculation specification for cmos asic libraries

    延遲計算和功率計算標準. cmos集成電路子程序庫.預布局延遲計算規范
  14. Based on the above work, the calculation formulae of nominal slamming pressure and the bearing capability of the bottom plates in the rules are modified, and the safety coefficients are evaluated referring to the target reliability specification, then the more reasonable formula of assessing the slamming strength of bottom of the bow is given

    在上述工作的基礎上，對我國建造規范中原有的砰擊壓力名義值和底板承載能力名義值的計算公式進行了修正，並參照選定的目標可靠性指標求出了安全系數，給出了更為科學合理的船首底部砰擊強度定值評定公式。
  15. In the actual ( ( code for steel structure design } ) ( gbj 17 - 88 ) and for the ( ( technical specification for steel structure of light - weight buildings with gabled frames ) ) ( cecs 102 : 98 ), the calculation method for the stability of the members is : obtaining the axial force through the analysis of the linear - elastic inner force of the whole structrue, then checking the stability inside and outside the plane respectively on the foundation of the yielding rule of the edge

    我國現行《鋼結構設計規范》 （ gbj17 - 88 ）和《門式剛架輕型房屋鋼結構技術規程》 （ cecs102 : 98 ）對構件的穩定計算方法是：先對構件進行整體線彈性內力分析，得到構件的軸力和彎矩；再根據邊緣屈服準則對構件分別進行平面內和平面外穩定驗算。
  16. The calculation results show that the value of crack width obtained from the new and old hydraulic design specification is different, especially, the member with thicker concrete protective layer, and that the value obtained from industrical and civil building design specification is larger than that from hydraulic design specification, so its design result is safe than hydraulic design

    實例表明新、舊規范的裂縫寬度值計算差異較大，特別是混凝土保護層厚度較大時，同時工民建規范計算公式的計算值較水工規范計算公式的值大，故偏於安全。
  17. Switching loss and efficiency of the proposed resonant pole zvt three - phase pwm inverter are analyzed and discussed. results of calculation and testing of the prototype together with a hard - switching inverter with the same specification show that an improvement of 2 % ~ 3 % is obtained. based on the analysis of drawbacks of existing svpwm technique in resonant pole zvt three - phase pwm inverters, several improved svpwm methods are presented

    對提出的諧振極零電壓過渡三相pwm逆變器的開關損耗和工作效率，進行了深入的分析和討論，並針對原理樣機進行了理論計算和實際測量，並與相同規格的硬開關三相逆變器進行了對比研究，結果表明，採用提出的軟開關技術的原理樣機的效率可以提高2 % 3 。
  18. 2. according to water resources and hydropower engineering specification for design of steel gate, mech - electric design handbook for hydropower station and with the consideration of the related theories on steel structure, this paper studies the design method and calculation theories of the plane gate. on the basis on above, the plain structure design subsystem is developed

    2 、依據現行的《水利水電工程鋼閘門設計規范》 、 《水電站機電設計手冊》 ，綜合相關的鋼結構設計原理，研究了平面閘門的結構設計計算方法並研製開發了平面閘門結構設計子系統。
  19. Design calculation specification for fuel combustion of chemical industrial furnace

    化學工業爐燃料燃燒設計計算規定
  20. Cmos delay and power calculation standards - part 2 : pre - layout delay calculation specification for cmos asic libraries

    延遲計算和功率計算標準.第2部分:互補金屬氧化物半導體
分享友人
分享到 Line

分享到臉書