cam angle 中文意思是什麼

cam angle 解釋
凸輪包角
  • cam : CAM ＝computer-aided manufacturing 計算機輔助製造，計算機輔助生產。n. 【機械工程】凸輪，偏心輪；靠模。
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角，隅，角落；棱，嬗角。2 【數學】角，角位，角的度數。3 【機...
  1. The paper also does some deep research on the mesh characteristic of the mechanism, analyses the cause o f the cam profile error and index error during working, using object - oriented method, vc + + and pro / toolkit, performs second development to pro / engineer, completes entity proplasm of the cam mechanism using only few parameters, the press angle calculate module, error analysis module and curvature calculate module are built on the basis of it

    然後通過對弧面分度凸輪加工中產生廓面誤差及工作時產生分度誤差原因的分析，建立了計算加工和分度誤差的數學模型。應用vc + +和pro toolkit對pro engineer進行二次開發，建立了弧面分度凸輪機構的參數化設計和三維造型及壓力角、誘導主曲率等運動特性和誤差分析軟體系統。
  2. The one used the actual locomotor orderliness gained by reverse seeking to amend the contour curve of the cam. the new academic contour curve of the cam and tracks of polar and right angle coordinates of the center of reamer were presented

    第一種是根據反求得到的實際從動件運動規律，修正了開牙凸輪輪廓曲線，給出了新的凸輪理論輪廓曲線和刀具中心極坐標軌跡和直角坐標軌跡。
  3. The other used a similar locomotor orderliness to substitute the original by compare. the new academic and actual contour curve of the cam and tracks of polar and right angle coordinates of the center of reamer were presented, too

    第二種是通過與原開牙凸輪機構從動件運動規律相比較，採用一種相似的運動規律來替代原運動規律，也給出了凸輪理論輪廓曲線、實際輪廓曲線和刀具中心軌跡。
  4. The acceptability our rejection and the depiction of some content in the course " mechanisms and machine theory " is discussed, ( e. g., group dividing, solving steps of the graphical method for vector equation, versions and methods for analytical kinematic analysis, inversion design for linkage mechanisms, crank angle between the two limiting positions, design formulae for cam mechanisms, classification of combined mechanisms, formula of the radius of addendum circle of gear, balancing of machinery, etc. ) and some new opinions are presented

    摘要就《機械原理》課程的某些內容（如：拆桿組的方法、矢量方程圖解法的解題步驟、運動分析解析法的版本和方法、連桿機構的反轉法設計、極位夾角、凸輪機構設計公式、組合機構的分類、齒輪齒頂圓半徑公式、機械的平衡等）的取捨和敘述進行探討，提出一些新的看法。
  5. Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism

    摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。
  6. Zeron has been buckling down to press related automation equipment and always provide products that achieve customer ' s cost reduction requirement from 2001, we offer : mechanical press cnc controller, digital cam, die height indicator, crank angle display, tonnage monitor, calibration load cell, and with cabinet ' s total solution for press control

    南京澤榮自動化系統有限責任公司自2001年以來一直致力於壓力機自動控制領域產品的開發、生產和銷售以滿足客戶降低成本、提高效率之需求，我們的產品包括:高速壓力控制系統，電子凸輪，模高指示器，轉角指示器，噸位監控系統，壓機標定系統，以及帶電控櫃的全套控制系統等
  7. To improve the transmitting characteristic and decrease the output work has a direct effect on the enhancement of the operating property and life - span of the operating mechanism of vacuum circuit breakes. based on the characteristics of polynomial rule of the cam movement, considering the pressure angle of cam device, an optimization model is established, with the coefficients of polynomial rule of cam movement as the optimizing variable, and the minimum output work of the mechanism as the object function. with the optimization tool box of matlab, the optimization process is conveniently completed and the perfect result of optimization design is obtained

    改善真空斷路器操動機構的傳動運動特性，減小真空斷路器的操作輸出功，對提高真空斷路器的操作使用性能及壽命都具有直接的影響.利用凸輪機構的多項式運動規律的特點，以凸輪多項式運動規律的多項式系數為優化變量，以斷路器操動機構最小的輸出功為目標函數，考慮操動機構合分閘時凸輪機構傳動壓力角的情況，建立了彈簧操動機構中凸輪機構的優化數學模型，並利用matlab語言的優化工具箱方便地實現了優化過程，得到了較理想的優化設計結果
  8. After analyzing the function requirement of cad / cae / cam for fiber placement, and interface for further developing of existing cad / cae / cam software, further developing ug is selected as developing strategy for realizing cad / cam functions for fiber placement, and ansys is selected for realizing the cae function for fiber placement. effects made by stacking - sequence and fiber orientation angle on stress concentration around holes for tensile open - hole composite plate is studied. a new idea, general layup of composite laminates is comprised of simply - steered plies and fully - steered plies, is presented

    本文就面向纖維鋪放的專用cad / cae / cam系統的軌跡規劃進行了相關研究，主要完成了以下幾方面的工作: 1 .基於纖維鋪放cad / cae / cam的需求，綜合分析了現有cad / cae / cam平臺性能及其二次開發介面，提出了應用ug平臺進行二次開發實現纖維鋪放cad / cam模塊與基於ansys平臺實現纖維鋪放的cae模塊相結合的開發策略。
  9. Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology

    系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
  10. Abstract : this paper explores the interelations between the work efficiency and the pressure angle of a cam machine, and expounds the theory of selecting and confirming for the optimal permissive pressure angle of cam, and introduces the design means that can be used in engineering practice

    文摘:探討了凸輪機構工作效率與機構壓力角之間的相互關系，闡述了選擇和確定凸輪機構最佳許用壓力角的理論，介紹了可用於工程實際的設計方法
  11. Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam

    摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
  12. Apply numerical arithmetic to calculate and smooth the profile, meanwhile apply numerical simulation to analyze the distributing disciplinary of cam ' s rotating angle and the response of displacement velocity and acceleration of slider

    利用數值演算法對其進行了曲線擬合和光順，同時，利用數值模擬方法，反求分析了滑塊從動件的位移、速度、加速度響應和凸輪的轉角分佈規律。
  13. Drivers kok ( cam degree angle ) : - axis rotation angle of hospitality require a degree movement. greater perspective, the more stable movement

    驅動角（凸輪分度角） ：入力軸旋轉角要求招待一次分度運動。角度越大，運動越平穩。
  14. Analysis of pressure angle for parallel indexing cam organ

    平行分度凸輪機構壓力角的分析
分享友人
分享到 Line

分享到臉書