cam contact 中文意思是什麼

cam contact 解釋
凸輪接觸
  • cam : CAM ＝computer-aided manufacturing 計算機輔助製造，計算機輔助生產。n. 【機械工程】凸輪，偏心輪；靠模。
  • contact : n 1 接觸；聯系；交涉。2 〈美國〉（有勢力的）熟人；門路。3 【數學】相切；【電學】接觸；觸頭；觸點...
  1. Firstly, the hertz contact theory is used to design the export moment of the prototype ; deformation status of the flexspine under the elliptical cam wave generator action is analyzed using the column shell theory, whose boundary condition is four force action. design proposal of the wave producer put forward considering the precision theory of rolling friction transmission

    首先用赫茲接觸理論對樣機的輸出力矩進行了設計;應用四力作用下的光滑圓柱殼體理論分析了在橢圓凸輪波發生器作用下柔輪的變形狀況，結合滾動摩擦副傳動精度理論提出了波發生器總體設計方案。
  2. Cam - west restaurants, attractive tableware, candles village, elegant environment, the french romantic thoughts ever, catering to the significance of philosophy, let you enjoy the feelings of contact, the elegant fun with friends, stands fully appreciate the art created

    琴語西餐廳，精美的餐具幽幽的燭光優雅的環境，浪漫雋永的法式大餐，將飲食賦予哲學的意義，讓您享受在聯絡感情廣交朋友的高雅樂趣之中，充分領略馨香的藝術情調。
  3. For developing the software, the contact pressure between the cam and the follower can be gained by traditional hertz theory formula

    為了有利於軟體的開發，在模擬中選擇hertz理論公式求解凸輪挺柱間的接觸應力。
  4. According to the characteristics of the overhead camshaft valve train, the author thoroughly analyzed the kinematics and dynamics concerned in the design of valve train cam profile. the results illuminate the influence of valve timing, ample factor as well as the contact stress between cam and tappet on the design of cam profile

    根據頂置凸輪軸式配氣機構的特點，文章深入分析了在配氣凸輪型線設計中必須涉及的運動學及動力學問題，說明了配氣定時、豐滿系數及凸輪與挺柱間接觸應力對凸輪型線設計的影響。
  5. The contact freeform surface meaurement system the authors are developing is introduced in this paper, it is the application of cmm in the reverse engineering of part. the components of its software and hardware are analyed. under the circumstances of cad modelis unknown, somecirtical problems are studied such as the measurement points adaptive localization, the measurement path, layout and measurement data disoposal etc. based on measuring the curved surface of the cam, the scaning software have be designed in measuring the curved surface in cmm. the cmm ' s data can transfer to cad / cam system

    分析了其軟硬體的組成，並對在cad模型未知的情況下，測量系統軟體中的一些關鍵技術，如測點的自適應分佈、測量路徑的規劃和測量數據的處理方法等作了研究。並以凸輪輪廓曲線為例，編制了相應的曲線面輪廓掃描軟體，並使三坐標測量機的測量數據轉換為cad cam能接受的圖形信息格式。
  6. Stop : stop rotating output shaft, cam rollers contact roller cam bearings taper ribbed support of the re - direct

    停止：出力軸停止旋轉，凸輪滾子接觸滾子軸承式凸輪錐度支撐肋的重直部分。
  7. The cam - follower is the main mechanism of the engine that carries out a series of accurate motions. its mild wear may gradually worsen the contact conditions. the probability for surface fatigue will then increase due to changes in the surface topography

    凸輪?挺柱是內燃機中實現一系列精確動作的主要機構，其磨損會使接觸條件惡化，由此產生的表面形貌的變化會使表面疲勞的概率增加，可能會對部件產生破壞性的影響，進行凸輪機構的摩擦學設計對提高內燃機的運行性能和延長使用壽命十分重要。
  8. Finally an integral software module for cam mechanism contact pressure analysis is developed in ansys. this work has formed an integrated technical route from geometrical design to tribological design. it may contribute to the theories of wear design and arithmetic, and can be used for reference to the cam - follower tribological design

    本文的工作形成了從凸輪幾何設計到摩擦學設計的一條完整的技術路線，已經可以基本作為內燃機凸輪機構摩擦學設計軟體系統的雛形，今後可以在此基礎上開發凸輪機構設計的專家系統軟體；本文還在完善工程磨損設計理論和計算方法方面有所貢獻，可以為凸輪機構的實用摩擦學設計提供參考和借鑒。
  9. After discussing the theoretical basis for a designing method of cam mechanism based on output force ( moment ) characteristics, a new designing method for that mechanism is presented and then, employed for designing a spring actuating mechanism in vacuum circuit breaker with singlephasy single breaker contact which operates under the condition of high - voltage and large - current. the application of this method shows that the cam mechanism designed by using the method presented can completely meet the requirement of output force characteristics for the mechanism and, furthermore, the performance of the mechanism is remarkably better than that of similar mechanisms designed by using conventional methods

    介紹了一種按輸出力（力矩）特性曲線設計凸輪機構的新方法.闡述了這種設計方法的理論依據，並將這種設計方法應用在高電壓等級、高工作電流單相單斷口真空斷路器的彈簧操動機構中.結果表明：用這種方法設計的凸輪機構完全能滿足機構所要求的輸出力特性的要求，且機構的性能明顯優于用傳統方法設計的機構
  10. 5 ) under the pro / engineer circumstance, the contact finite element analysis method of the spatial cam sliding tooth transmission are established ; using the i - deas software, the corresponding contact finite element analysis has been done. comparing

    5 ）在pro / engineer環境下建立了空間凸輪活齒傳動的接觸有限元分析模型，運用i - deas軟體進行了相應的接觸有限元分析，並將有限元分析的結果與基於赫茲理論的計算結果進行了對比分析，二者吻合。
  11. The application of 3d object surface measurement is more and more important in the domain of industrial inspection, quality controlling, machine vision, cad / cam, and medical science, etc. and because of its high precision, nondestructive feature and also fastness of data acquisition, the method of non - contact optical measurement becomes very popular

    三維物體表面輪廓測量技術在高速在線檢測、質量控制、機器視覺、反求工程、 cad cam以及醫療診斷等領域的應用日益廣泛。具有非接觸特性的光學測量方法由於其高解析度、無破損、數據獲取速度快等優點而被公認為最有前途的三維輪廓測量方法。
  12. Major contents of the thesis are as follows : 1 ) based on brief introduction of the profile theory about the spatial cam sliding tooth transmission, those formulas correlated to the mechanics feature are deduced to calculate the geometrical parameters ; 2 ) according to the hertz contact theory in elastic - mechanics, the mechanics analysis model of the spatial cam sliding tooth transmission is built up ; the deformation harmonizing conditions at each contact point are erected ; the force analysis formulas of point contact are deduced and the resolution method is presented ; 3 ) the numerical calculating software about the deformation of the spatial cam sliding tooth transmission is developed ; using the software, the force characteristics of the spatial cam sliding tooth transmission are calculated with different design parameters ; the general law on force characteristics of this transmission is obtained

    論文的主要內容包括： 1 ）在簡要介紹空間凸輪活動傳動齒廓理論的基礎上，推導了與力學特性相關的幾何參數的計算公式。 2 ）建立了空間凸輪活動傳動的力學分析模型；依據彈性力學赫茲接觸理論，建立了各接觸點之間的變形協調條件，推導了空間凸輪活齒傳動點接觸受力分析公式，並給出了求解的方法。 3 ）開發了關于空間凸輪活動傳動受力變形的數值計算軟體；應用該軟體，對不同設計參數的空間凸輪活齒傳動的受力特性進行了數值計算，獲得了該傳動受力變形的一般規律。
  13. The author proposes a new contact point regress method which can be applied to any type of sc profile inspection by use of coordinate measuring machine ( cmm ), establishes a mathematical model for data processing and error evaluation method, solves the puzzles of the spatial cam profile inspection and error calculation

    提出了以三坐標測量機為工具，適合於任何形式空間凸輪廓面檢測的接觸點回歸法，給出了數據處理的數學模型和誤差計算方法，解決了空間凸輪廓面檢測與誤差計算的難題。
分享友人
分享到 Line

分享到臉書