carburizing 中文意思是什麼

carburizing 解釋
滲碳，碳化
  1. Study on gas carburizing technique of instillation with kerosene - carbinol

    甲醇滴注式氣體滲碳工藝的研究
  2. Research on high - density carbonization of carburizing steel

    滲碳鋼高濃度滲碳的研究
  3. The case-hardening or carburizing process is in wide use.

    表面淬火或滲碳法應用十分廣泛。
  4. New process of drop feed gas carburizing with high rate

    滴注式快速氣體滲碳新技術
  5. Gear pre - oxidation gas carburizing at low temperatrue

    齒輪預氧化低溫氣體滲碳
  6. Experimental verification of cad software for gas carburizing

    軟體的試驗驗證
  7. Carburizing steels of bearing for freight rolling bearing

    鐵路貨車滾動軸承用滲碳軸承鋼
  8. Study and application of pulse gas carburizing technology

    脈沖式氣體滲碳技術研究和應用
  9. Improvement of workholders for gas carburizing pit - type furnace

    井式氣體滲碳爐工裝改進
  10. Specification for steel forgings, alloy, for carburizing applications

    滲碳合金鋼鍛件規范
  11. Drop feed well type gas carburizing furnace

    滴注式井式氣體滲碳爐
  12. Carburizing or carbonitriding and post - quenching and tempering of steel part

    鋼件的滲碳與碳氮共滲淬火回火
  13. Study on the abrasion behavior of carburizing carbonitriding steel for pump body

    碳氮共滲鋼水泵體的磨損特性研究
  14. Gas carburizing and carbonitriding

    可進行氣體
  15. Process of carburizing and carbonitriding, quenching and tempering of iron and steel

    鋼鐵的碳化氰化淬火和回火處理
  16. Abstract : the effect of different carburizing programs on the microstructure and thick of carburized layer of screw bevel gears has been studied, meanwhile the fatigue life of these gears has also tested

    文摘:本文研究了不同滲碳淬火工藝對螺傘齒輪組織及滲層深度等影響，並對螺傘齒輪進行了臺架疲勞測試。
  17. With the software of simulating low - pressure vacuum carburizing process and computer control system, carburizing process parameters are controlled accurately. the minimum error of carburizing layer depth, the optimal distribution of carbon concentration in carburizing layer and the minimum distortion are insured

    均勻布置鼠籠狀加熱元件和多組滲碳氣氛噴嘴，並對滲碳參數進行精確控制，可保證零件最小的滲層深度誤差最佳的滲層碳濃度分佈。
  18. It is shown from results that increasing carburizing time further in the normal technology can not obviously deep the carburizing layer, but can cause nonmartensite microstructure at the bottom of the gear and coarse grain across the gear, these will heavily decrease the fatigue life of the gear

    結果表明：在正常滲碳淬火工藝基礎上再延長滲碳淬火1小時，齒輪滲碳層深度變化不大，但其齒根局部表面處有非馬組織，且晶粒尺寸易產生異常長大現象，從而致使臺架疲勞壽命明顯下降。
  19. Specification for carburizing steels of bearings

    滲碳軸承鋼技術條件
  20. Standard specification for carburizing steels for anti - friction bearings

    耐摩擦軸承用滲碳鋼的標準規范
分享友人
分享到 Line

分享到臉書