case of bending 中文意思是什麼
case of bending
解釋
彎曲狀態-
Conducting wire core composed by thin brass wires or tinning brass wires, it is very soft. surface of part leads wraped mylar isolation layer, in case affecting their bending performance
導電線芯採用較細的銅絲或鍍錫銅絲束絞組成，導線極其柔軟，部分產品的導線表面包有聚脂薄膜隔離層，以免絕緣橡皮嵌入其邊縫中而影響彎曲性能。 -
Permissible min. bending radius : no less than 6 times of the completed cablediameter in case of unarmoured cable ; no less than 12 times of the completed cable diameter in case of armoured or copper tape screened cabel ; no less than 6 times of the completed cable diameter in case of screened flexible cabel
3電纜的允許彎曲半徑：無鎧裝層的電纜，應不小於電纜外徑的6倍；有鎧裝層或銅帶屏蔽結構的電纜，應不小於電纜外徑的12倍；有屏蔽層結構的軟電纜，應不小於電纜外徑的6倍。 -
Aiming at technical features and technology requirements for cold bending forming production line of steel bar for packing case, equipment including in such line has been introduced with emphasis on working principle and devices for burr trimming and opening piercing, on control principle of hydraulic expanding and flying shearing on the line
摘要針對包裝箱鋼條冷彎成形生產線的技術特點及產品工藝要求，介紹了包裝箱鋼條冷彎生產線的設備組成；重點闡述了包裝箱鋼條的在線預沖毛刺及豁口孔設備的工作原理及裝置、包裝箱鋼條產品的在線液壓擴孔及液壓飛剪技術的控制原理。 -
The probable reasons for breakage in this case were usage of a small ( 30 - gauge ) needle and improper bending of the needle
發生斷針原因可能是使用較小的針頭及不當彎曲針頭所造成。 -
This can be a basis for eliminating the case crack damage by restraining the occurrence of the dangerous bending moments through improving the mounting conditions of the power - train system
這為通過改進傳動系的支承條件，避免殼體出現早期破裂損壞提供參考依據。 -
Since the similarity between plane elasticity and plate bending is a special case of the static - geometric analogy, this paper, therefore, studies the new formulation based on the static - geometric analogy in a broad sense
平面彈性和板彎曲的相似性是殼體靜力?幾何比擬的特例，所以在總的意義下本文就是研究基於板殼靜力?幾何比擬理論的新型板殼單元列式。 -
Depending upon stiffness and strength requirements, this transfer of bending moments can be achieved by either semi - rigid or rigid beam - column connections. in both case, the intersection between beams and columns ( the beam - column joint ) will be subjected to high shears
本文從節點域的屈服過程，破壞機理入手，採用虛功原理，對節點域屈曲進行了推演，得到了節點域破壞的最大剪力，以及屈服后所能承受的剪力。 -
4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented
4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
分享友人