casing deformation 中文意思是什麼

casing deformation 解釋
套管變形
  • casing : n. 1. 裝箱，裝袋，入鞘。2. 〈集合詞〉包裝箱[鞘、袋、筒、框等]。3. （窗等的）框子；圍子；圍墻。4. （做香腸用的）腸衣。5. 外（車）胎；套管；罩殼。
  • deformation : 變形,走樣
  1. It can lead to not only quick wear and early failure of drill pipe but also the decrease of collapse resistance and burst resistance of casing string, which could cause casing collapse, casing deformation and casing leak, even well bore abandonment

    其直接後果是：鉆柱快速磨損，導致過早失效；套管磨損會降低套管柱的抗擠強度和抗內壓強度，造成套管柱擠毀、變形及泄漏，嚴重時造成全井報廢。
  2. Abstract : the stimulation treatment of & quot; loosening rock by the dilatancy of explosive waves & quot; is tested in the casing well 4242 for studying its result and its influence on casing. the result of the field test shows that this test is successful in technology, the oil production of the well is 4 times as much as that of it before the test ; the deformation of casing is local, and the result of the strength calculation shows that the deformation will not destroy casing

    文摘:為了研究「壓脹松動」增產技術的增產效果和對套管的影響，在延長石油管理局子長油礦對4242井進行了現場實驗.該技術採用強動載波在地層深處疊加的方法，造成壓脹條件，松動巖石，增大近井帶滲透率，提高油井產量.施工后，該井產量增加為原來的4倍多.本次實驗工藝上是成功的，首先是按設計要求引爆了炸藥，其二是由於採取了保護措施，使套管變形局限在施工段處，不影響下泵，不影響油井生產;套管強度校核分析也證明了套管不會破壞.施工后地質效果明顯
  3. And the finite element method ( fem ) was used to simulate the stress and deformation of the outer casing and the bearing chock. on the basis of the experiments and fem analysis, the strength and fatigue lifetime, the interaction of creep and fatigue lifetime, the creep lifetime of outer casing and bearing chock have been analyzed, at the end of trail, sem analyses of failure section has been conducted

    同時對航空發動機燃氣渦輪外機匣和軸承座進行了有限元模擬計算，得到外機匣和軸承座的焊接處的強度和變形情況的模擬結果。根據試驗數據和有限元的計算結果，對發動機燃燒室外機匣和軸承座兩種結構（包含焊縫）進行靜強度分析、疲勞壽命分析、蠕變壽命分析、蠕變疲勞交互作用壽命分析以及斷口的金相分析。
  4. The surface of natural fracture ( crack ) is parallel to the orientation of maximum principal stress. the principle orientation of anisotropic permeability reservoirs agrees with the orientation of the maximum principle stress. many engineering problems ( e. g. bore - hole stability, casing deformation failure during drilling, reasonable arrangement of wells, the optimum design of hydraulic fracture and so on ) are influenced by the in - situ stress orientation

    天然裂縫面和裂隙面與最大主應力方向平行；在各向異性低滲透率油田中主滲透率方向與最大水平主應力方向趨向一致：在鉆井過程中井壁穩定性，套管變形和損壞，油田開發井網合理布置、水力壓裂優化設計等都與地應力方向有關。
  5. The software of analysis method of multi - armed caliper log imaging has been developed, and the on - site applied results show that the software can get the casing maximum drift diameter and effective drift diameter and simultaneously give the caliper hoop extension graph and cross section graph in arbitrary depth which can diagnose the sort and degree of casing deformation

    摘要研製了多臂井徑成像測井解釋方法軟體，現場應用結果表明：運行該軟體可以解釋得到套管最大通徑、有效通徑；同時給出任意深度井徑周向展開圖、橫截面圖，進而可判斷套變的種類和程度。
  6. The method of surfacing welding sealing strip was adopted to repair the deformation of the flange joint surface of the high and intermediate pressure outer casing

    摘要湛江發電廠在1999年1 （上標# ）機組大修中採用堆焊密封帶方法修理了汽輪機高中壓外缸中分面的變形缺陷。
分享友人
分享到 Line

分享到臉書