center distance change 中文意思是什麼

center distance change 解釋
中心距變動
  • center : n vt vi 〈美國〉=centre n 1 中心;中心點;圓心;中央;中樞,核心;中心人物;根源,起源。2 〈常C ...
  • distance : n 1 距離,路程。2 遠隔,遠離;遠處,遠方。3 (時間的)間隔,長遠,長久。4 懸殊。5 隔閡,疏遠。6 ...
  • change : vt 1 改變,變更,變換,變革。2 交換;兌換;把(大票等)換成零錢;把(支票等)兌成現金。3 換(車、...
  1. While the brother was speaking with his co - workers about a new layout, the exhibition s organizer unexpectedly removed two wooden walls around the stage area that had been blocking the view of master s picture. this change created a much more open view of the tainan center s display so that even from a distance people could see master s large, magnificent photo, and the crowds congregating in front of the stage could conveniently access the booth

    師兄與工作人員協商移動位置后,主辦單位竟然也把舞臺區的兩面木墻拆了,我們攤位的視野剎時豁然開朗,來往人群在遠處就可看到師父美麗莊嚴的大法相,舞臺區聚集的人潮常順便來到我們的攤位叄觀。
  2. Since the suggested method makes a significant improvement in wind speed, it is more suitable for wind field estimation over complex terrain than other methods which only concerns the effect of distance. then we calculate the wind change with evaluation, last we can conclude the wind abase the hilly terrain, we find the wind in westward and center plain is much smaller than other area. while the wind in northward hilly area is much bigger with the hilly arising. the wind of chongqing is the biggest period in spring ( april ), the smallest period in winter ( january ), the wind in summer ( july ) is bigger than its in autumn ( october )

    本文利用重慶及其周邊地區的常規氣象站的1951 ? 1980年30年的風速平均資料,針對復雜地形風速診斷,以地理信息系統為數據處理平臺,根據重慶1 : 25萬dem數據,來獲得重慶市實際復雜地形的高程,提出了一種適合於起伏地形的權重內插方法,通過引入一個表示地形起伏變化程度的因子,構造了一種新的權重函數,來處理復雜地形上的風速,通過與只考慮距因素同反平內插方法比較發現,本方法更適合在起伏地形條件下使用;然後根據經驗公式在地形上進行計算,得出重慶地區起伏地形下的風速分佈;得出重慶市的西部、中部平原地帶風速較小,而北部山區隨海拔高度升高風速也較大;重慶市風速最大時期為四月份,冬季一月份最小,夏季(七月份)大於秋季(十月份) 。
  3. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上,提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
分享友人