cermet resistance 中文意思是什麼

cermet resistance 解釋
塗釉電阻, 金屬陶瓷電阻
  • cermet : n. ＝ceramal.
  • resistance : n. 1. 抵抗，反抗，抗拒，抵禦；敵對，抵抗力，反抗力，阻力，【生物學】抗病性。2. 【電學】電阻；阻抗；電阻器。
  1. The mechanism of corrosion and erosion resistance of nicr alloy and cermet coatings were explored and their performance were compared with 20g, 20g covered by dope and the coatings of fecral, nicrti used widely at present

    並將由這些新的塗層材料和目前廣泛使用的fecral ， nicrti以及與未加以保護的20g基體和刷塗料保護的20g在抗高溫氧化、高溫腐蝕、耐沖蝕磨損和熱震性等方面加以比較。
  2. For xrd, ellipsometry examinations, single - side - polished si ( lll ) wafers were used as substrates and for resistance measurement, glass was used and for infrared examination, double - side - polished si ( lll ) wafers were used and for ultraviolet - visible spectrophotometry, double - side - polished quartz wafers were used and for tem micrograph and electron diffraction pattern observation, cu nets deposited by formvar film were used. the cu - mgf2 cermet films were from 50 to 600nm thick

    用於xrd分析、橢偏測量的單拋si （ 111 ）晶片和電阻測試的載玻片上淀積膜厚約為600nm ；用於ir測試的雙拋si （ 111 ）晶片和uv測試的石英玻璃片上淀積膜厚約為250nm ；用於透射電鏡分析的樣品則淀積在400目銅網上的支撐formvar膜上，膜厚約為50 100nm 。
  3. The experiments showed that wc and vc can dissolve mutually in the carbonizing reaction. when wc ' s content exceeds vc ' s, vc will dissolve into wc and make wc ' s crystal lattice bring aberrance and become wc1 - x, contrarily when vc ' s content exceeds wc ' s, wc will dissolve into vc and also make vc ' s crystal lattice bring aberrance. the surface cermet composite has high rigidity and well wear - resistance

    （ 7 ）採用鑄造燒結技術，通過加入毗顆粒和v班一vc的原位放熱反應成功制取了碳化物陶瓷質量百分數超過60 %的表面金屬陶瓷材料，實驗證實wc與高溫碳化反應生成的vc相互可以很好的固溶，當wc的含量超過vc時， vc可以固溶到wc中，使wc的晶格發生畸變，成為昵卜: ，反之當vc的含量超過wc的含量時， wc可以固溶到vc中，也會造成vc的晶格畸變。
  4. The vc - fe surface composite shows high wear - resistance, it ' s wear - resistance is 4. 20 times as that of chilling respectively. with the content of v increasing, it ' s rigidity and wear - resistance increases continually. more vc grains gained, and well distributed, better wear - resistance the vc - fe surface composite will show. ( 7 ) surface cermet composite was formed by the means of cast - sintering technique, with the help of adding wc grains and the quantity of heat sent out from the reaction v + c vc, the carbide cermet quality percent exceeds 60 %

    在重載干滑動摩擦條件下， vc一fe表面復合材料顯示了很高的耐磨性，其相對耐磨性是可淬硬鑄鐵的4 . 2倍:隨著含v量的增加， vc一fe表面復合材料的鑄態硬度和耐磨性不斷提高， vc顆粒越多，分佈越均勻，表面復合材料的耐磨性就愈好。
  5. Cermet resistance element

    金屬陶瓷電阻元件
  6. Thermal shock resistance and ablation behaviour of titanium diboride - copper - nickel cermet

    金屬陶瓷的抗熱震和抗燒蝕行為
分享友人
分享到 Line

分享到臉書