circular joint 中文意思是什麼

circular joint 解釋
環接
  • circular : adj 1 圓的，圓[環]形的。2 循環的；巡迴的。3 通告的，環游的；供傳閱的。4 夥伴的，團體的。5 【邏輯...
  • joint : n 1 接合，榫接合處，接合點。2 【解剖學】關節。3 【植物；植物學】節。4 【電學】接頭。5 【建築】接...
  1. Joint angle and delay estimation based on uniform circular array in cdma system with aperiodic spreading code

    非周期擴頻系統中基於均勻圓陣的角度和時延的聯合估計
  2. Circular sight glasses with case in metal to metal contact type flanged joint

    金屬與金屬接觸式法蘭連接中的有罩圓形觀察孔
  3. Rotation - invariant target detection by using a modified fringe - adjusted circular harmonic joint transform correlator

    修正條紋調節的圓諧聯合變換相關器作旋轉不變的目標檢測
  4. Based on the cause analysis for failure of water stop of tunnel ' s cast in site circular construction joint from theoretical and constructional point of view as well as the working mechanism of expansive water stop proposed in terms of width of construction joint, the relation between width of circular construction joint and water pressure resistance of water stop is established and its model test carried out

    首先從理論和施工角度分析了隧道現澆環向施工縫止水條的失效原因，然後從施工縫張開度的角度提出了膨脹止水條止水的原理，在此基礎上建立了施工縫張開度與止水條抗水壓力之間的關系，並進行了模型試驗。
  5. The circular ring joint bonnet seal has proven to be the best bolted high pressure bonnet joint available

    這種圓形環狀連接閥蓋密封經過實踐證明是目前最好的螺栓高壓閥蓋連接。
  6. The circular male and female bonnet joint is self - aligning and encapsulates the gasket

    圓形外螺紋和內螺紋閥蓋連接是自行對準調整並且封裝的墊圈。
  7. The company is a sino - foreign joint - venture enterprise, incorporating smelting, electroslog, refining, forging, steel rolling and tool manufacturing. it has production lines for high speed steel, mould steel, hss circular saw blades, face - sides cutters, mould, blocks, pre - hard fine plate, garden knives, alloy special cutters and planer knives, as well as six production lines for heat treating. the nano coating center is production base for tool & mould steel productions in domestic

    公司是一家集冶煉、電渣重熔、鍛造、軋鋼、精整、工具製造於一體的中外合資企業，擁有高速鋼、冷、熱作模具鋼生產線，高速鋼圓鋸片、三面刃銑刀、模具預硬精板、木工刨刀生產線，高溫熱處理、表面鍍層研發加工中心，是國內最專業的工模具鋼製品化生產基地。
  8. Standard joint is a circular male and female configuration with a corrugated metal gasket

    標準連接是圓形外螺紋和內螺紋結構，配置波紋金屬墊圈。
  9. This paper includes three parts of research : ( 1 ) cyclic loading tests of sixteen interior joints with rectangualr columns and four joint subassemblages with circular columns

    本論文進行了以下三方面的研究工作：進行了8組共16個矩形柱中間層中節點和4個圓柱節點組合體的低周反復加載試驗。
  10. The creative results are as follows : ( 1 ) behavior of the stirrup legs in the loading direction in the joint core ( along the loading direction for circular stirrups ) is different from that perpendicular to the loading direction. the stirrup legs in the loading direction acts as the tension chords in the truss model to resist shear, in the meantime, they confine the compressed diagonal strut from lateral expam - sion

    沿受力方向箍肢（或部位）既作為桁架機構的拉桿參與抗剪又對斜壓桿受壓后沿受力平面側向膨脹的水平分量起約束作用；垂直受力方向箍肢（或部位）原則上僅對斜壓桿沿垂直受力方向側向膨脹起約束作用。
  11. Circular spider type joint

    十字叉連接
  12. A blind joint angle and delay estimation method based on trilinear alternating least square technique in uniform circular array ( tals - cjade ) is also presented in section 3, and a blind joint angle and delay estimation method based on complex parallel factor in uniform circular array ( comfac - cjade ) is given to improve the tals - cjade convergence performance

    傳統聯合角度和時延估計方法在過載情況下（用戶數大於陣元數）不能正確估計。與傳統聯合角度和時延估計方法相比， tals - ljade和tals - cjade演算法具有較好doa和時延的聯合估計性能，且在過載情況下仍有較好的性能。
  13. Circular economy and market economy have the relationship of synchronization and joint improvement

    摘要循環經濟與市場經濟之間具有協同共進的關系。
分享友人
分享到 Line

分享到臉書