clearance angle 中文意思是什麼
clearance angle
解釋
后角-
Coherent with his metaphysics is his idea at survival clearance, which deepens self consciousness in both atomology and monadism from the angle at survival philosophy
與雅斯貝斯的形而上學思想相配合的，是他關于生存澄明的觀念，這種觀念從生存哲學角度出發深化了原子論與單子論蘊涵的自我意識觀念。 -
Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。 -
Analytic relationships among radial clearance, axial clearance, contact angle, center distance between two grooves, and bearing fit gap are derived for bearing design ; 3. analytic relations of radial fit gap and radial clearance is derived for bearing production
推導出了雙列角接觸球軸承的軸向游隙與徑向游隙、雙溝溝心距及軸承配套間隙之間的解析關系式，可應用於軸承設計。 -
Discussion again on principle effect of side clearance angle to cutting surface roughness
鋸料角影響鋸切表面粗糙度機理再探 -
Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied
然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。 -
Considering joint clearances at both ends of the coupler, a continuous contact model is developed by modeling clearance as a massless rigid link. a set of strongly nonlinear equations is obtained by using angle displacement of clearances in kinematic pairs as generalized coordinates. four order rong - kutta method is adopted to solve the dynamical equations of continuous contact model
考慮曲柄與連桿、連桿與滑塊之間運動副間隙，將運動副間隙看成是一無質量的理想桿，利用連續接觸模型進行建模，採用運動副間隙角作為廣義坐標，得出一組強非線性方程組。 -
Based on the comparison made among the characteristics of different kinds of the blade materials, the relationship between the material characters and the flow attack angle is explained, and then the breakage mechanism of the combined effects from both the clearance - cavitations and the erosion of leakage flow are expounded comprehensively
通過對不同材料的特性比較，解釋了材料特性與沖角之間的關系，綜合闡述了泄漏流動所引起葉片正面頭部空蝕與磨損聯合作用產生破壞的機理。 -
By comparing the ideal joint and clearance joint for the deployment process of a spatial deployable truss structure in multibody dynamics, it is found that the existence of the joint clearance makes the movement discontinuous, and also found the attitude angle degree and angle velocity of the spacecraft are affected in the deployment for the joint clearance
通過對有無鉸接間隙的剛性空間展開桁架模型的計算結果比較，說明鉸接間隙的存在對于桁架展開過程的影響及這一過程對衛星的姿態角速度的影響，同時比較了有無鉸接間隙時鉸接處在展開過程中接觸力的變化。
分享友人