clearance distance 中文意思是什麼
clearance distance
解釋
凈距離-
Measuring of clearance and creepage distance
電氣間隙爬電距離測定 -
Different safety standards have different requirements for the clearance and creepage distance of the limits of different calculation methods and results
摘要不同的安全標準對電氣間隙和爬電距離有不同要求，其限值的求法和結果不盡相同。 -
Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。 -
In this paper, a switch power circuit is given as an example to introduce how to confirm the minimum clearance and creepage distance with working voltage on different safety standards
今以一開關電源電路為例，介紹在不同標準下如何根據工作電壓情況對最小電氣間隙和爬電距離值進行確定。 -
Secondly we use canny arithmetic operators to get the edge of image, and remove the short link of edge then link the edge with small clearance. at last we can calculate the distance of conductor and the width of conductor according to the grade direction to detect of defect of the circuit boards
然後選用canny運算元提取導線邊緣，並對邊緣進行短分支去除和邊緣連接處理，最後根據梯度方向來計算導線間距離和導體寬度，以此來判斷電路板缺陷。 -
Analytic relationships among radial clearance, axial clearance, contact angle, center distance between two grooves, and bearing fit gap are derived for bearing design ; 3. analytic relations of radial fit gap and radial clearance is derived for bearing production
推導出了雙列角接觸球軸承的軸向游隙與徑向游隙、雙溝溝心距及軸承配套間隙之間的解析關系式，可應用於軸承設計。 -
Edge clearance : the smallest distance from any conductors or components to the edge of the pcb
邊安全間距：導線或元件到pcb邊的最小間距。 -
Abstract : the paper suggests two methods for adjusting the mesh clearance in cylindrical worm drive : one is to adjust the meshing center distance of worm gears, the other is to use dual lead cylindrical worm, introducing briefly the principle of adjustment and making a comparison between the characteristics of the two methods
文摘:提出了兩種調整圓柱蝸桿傳動嚙合側隙的方法:通過改變蝸輪蝸桿的嚙合中心距來改變其嚙合側隙;採用雙導程蝸桿傳動以調整蝸輪蝸桿的嚙合側隙，簡述了調整原理，並比較了兩種調整方法各自的特點。
分享友人