closed loop performance 中文意思是什麼

closed loop performance 解釋
閉環性能
  • closed : adj. 1. 關閉著的，封閉著的；密閉著的；保密的。2. 〈美國〉準備好了的；定了契約的。3. 【語音】閉音節的。
  • loop : n 1 （用線、帶等打成的）圈，環，匝，框，環孔，線圈；【醫學】（常 the loop）宮內避孕環。2 環狀物，...
  • performance : n. 1. 執行，實行，履行；完成；實現；償還。2. 行為，動作，行動；工作。3. 性能；特性。4. 功績；成績。5. 演奏；彈奏；演出；（馴獸等的）表演；把戲。6. 【物理學】演績。
  1. At first, the dynamic mathematic model is created in the light of the known dimensions and structure. then base on the mathematic model, dynamic analysis of the system is studied by drawing the open - loop bode diagram closed - loop bode diagram and step response curve using the analysis and calculating function of matlab. the influence factor on frequency character steady and performance of the system is also analyzed

    首先，根據已確定的尺寸參數和結構需要，計算並建立起系統的動態數學模型，然後在已知系統數學模型的基礎上，利用matlab語言強大的分析計算功能，對系統進行動態分析，通過畫出系統的開環bode圖、閉環bode圖及系統的階躍響應曲線，分析了系統的頻率特性、穩定性及系統性能的影響因素。
  2. A method of fuzzy optimization design based on genetic algorithm is presented as a new method of parameter optimization design for dc double closed loop speed adjusting system. the method covers three steps. firstly, speed overshoot rate and settling time are chosen as performance indice according to the demand of engineering. these indice are normalized by using fuzzy membership function and then weighted to form objective function of optimization model of the system. secondly, the dynamic response curve of the system with corresponding parameters and peoformance indice are obtained by computerized numerical calculation and simulation. finally, parameters of engineering design are expanded as searching space ; and parameters of speed regulator and current regulator are taken as genes in chromosome. these genes in searching space are optimized to get best solution by way of genetic algorithm. as shown by experimental results, the parameters designed by this method are capable of significantly improving performance indice of the system, which proves that it is a practical and effective method

    提出一種基於遺傳演算法的直流雙閉環調速系統參數優化設計方法.根據工程技術的要求，選用速度超調量和過渡時間作為參數優化性能指標.將該指標用模糊隸屬度函數歸一化，再加權平均形成系統優化模型的目標函數.採用計算機數值計算方法，通過模擬獲得系統對應參數的動態響應曲線及其性能指標.最後以工程設計的參數為搜索范圍，以速度調節器和電流調節器的參數為染色體中的基因，通過遺傳演算法在搜索范圍中優化這些基因，獲得優化解.實驗結果表明，所設計的參數能使系統性能指標有顯著提高
  3. Finally put the tse into the iffcs and used matlab5. 3 to conduct a digital simulation on the whole closed - loop for the purpose of testing the tse " performance in and influences on the iffcs, the output curves show the tse also works pretty well and cuts the mustard

    模擬結果表明目標狀態估計器的設計滿足性能指標的要求。最後，將目標狀態估計器加入到綜合飛行/火力控制系統中進行閉環數字模擬以驗證目標狀態估計器設計的性能，模擬結果說明其性能是符合要求的。
  4. In order to improve the control performance of the closed - loop system, the adaptive compensation term of the approximation error is introduced

    為改善控制系統的性能，引入逼近誤差的自適應補償項。
  5. It is shown that the proposed scheme guarantees the stability of the closed - loop system and achieves tracking performance idex, meanwhile the influences of external disturbance, neural network approximation error and the cross - coupling of input to output on the tracking error are reduced to a prescribed level

    該方法不僅保證了閉環系統的穩定，而且使外部干擾、神經網路逼近誤差及輸入對輸出的交叉耦合對跟蹤誤差的影響衰減到給定的水平。
  6. In this part, for a more general kind of systems, we give the design method of a robust adaptive controller based on backstepping technique, and analyxe stability and performance of the closed - loop system

    該部分對于更一般的一類系統，給出了一種基於反推技術的魯棒自適應控制器的設計方法，分析了閉環系統的穩定性和性能。
  7. The mrafc scheme employs a reference model to provide closed - loop performance feedback for generating or modifying a fuzzy controller ' s knowledge base. the adaptive compensation term of optimal approximation error is adopted. by theoretical analysis, the closed - loop fuzzy control system is proved to be globally stable, with tracking error converging to zero

    該方案利用參考模型作為閉環系統的反饋信號來產生、調節模糊控制器的規則庫，並通過引入最優逼近誤差的自適應補償項來消除建模誤差的影響，不但能保證閉環系統穩定，而且可使跟蹤誤差收斂到零。
  8. In the body of the dissertation, different performance indexes are defined and analyzed based on the analysis of different types of fwl errors in digital controller, and different fwl digital controller design and realization problems are considered and solved. the major contributions of this dissertation are as follows : considering the fwl errors of controller coefficients, define and analyze the closed - loop transfer function sensitivity measure with respect to the controller coefficients, obtain the optimal controller realizations via minimizing the transfer function sensitivity measure

    本論文首先對數字系統，特別是數字控制器設計與實現中的有限字長問題和非脆弱控制器設計的背景、歷史發展情況等作了簡單介紹，然後通過分析數字控制器中不同來源的有限字長誤差，定義不同的性能指標，較系統地分析並討論不同的有限字長數字控制器設計和實現問題。
  9. This new fuzzy optimization control method was applied to a superheated steam temperature control system, and simulation results verify the satisfactory closed - loop performance of the proposed fuzzy control system

    將這種新型模糊優化控制方法應用於過熱汽溫控制系統進行模擬，結果表明可以獲得非常滿意的閉環控制效果。
  10. When running in closed - loop system, the motor will be affect inevitably by load disturbance ? and disturbance due to variety of motor parameter, then the dynamic performance of closed - loop is affected

    無刷直流電機閉環運行時，不可避免地要受到外部負載擾動和由於電機本身參數變化而產生的干擾。因此，電機閉環控制系統的動態性能就會受到影響。
  11. Based on this scheme, the control system architecture is designed. based on this system ’ s necessary, the signal conditioning interface box is designed, it is used in the conditioning of sensor and the design of drive circuit, the software of controller is also developed, finally, the performance index of controller is validated by a closed - loop simulation test system with aero - engine model and digital controller

    根據此方案，確定了模擬平臺中控制系統的體系結構，根據系統的需要，設計了信號調理介面機箱，實現了對傳感器信號的調理及驅動電路的設計，並進行控制器軟體的開發，最後利用發動機數學模型和數字電子控制器組成閉環模擬環境，以驗證控制器的各種性能指標。
  12. Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail

    針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。
  13. After analyzing compensation conditions for 3 - axis stabilization to overcome disturbance from ship surge, sway and yaw, two control strategies - feed - forward compensation and closed - loop feedback compensation - are given. these two strategies are applied to antenna stabilized tracking system with good performance. intelligent pid is used in closed - loop feedback compensation to get high tracking precision and rapid response

    重點分析了天線穩定控制系統的三軸補償條件，提出了穩定系統抑止載體擾動的控制策略：對于橫滾和俯仰系統採用前饋補償的控制策略；對于方位系統，在以步進電機為驅動元件的特定條件下，研究了變控制周期的閉環反饋策略，同時成功將智能pid演算法應用於實際系統，提高了系統的跟蹤精度和響應快速性。
  14. This topic discusses the back - emf zero - crossing detection, the method of phase judging and compensation in detail. in order to improve the speeding performance we adopt the digital closed - loop speed control strategy

    詳細介紹了反電動勢過零檢測、相位判斷及相位補償的原理及實現方法，並且為了在較寬范圍內提高bldcm的調速性能，採用了數字式轉速閉環控制。
  15. On the base of roundly analyzing and studying the running mode of the sensorless bldcm, we explain theories and realizable methods of detecting back electromotive force, phase verdict and phase compensation in detail. in order to improve the timing performance, the control strategy of this system is to use digital speed closed - loop control

    在全面分析研究了無位置傳感器無刷直流電動機運行方式的基礎上，細致闡述了反電勢過零檢測、相位判斷及相位補償的原理及實現方法，並且為了在較寬的范圍內提高bldcm的調速性能，採用了數字式轉速閉環控制。
  16. Only routine closed - loop operating data and knowledge of the process time delay are needed using minimum variance as a benchmark in controller performance assessment

    用最小方差準則來評價控制器的性能，僅需過程變量的常規閉環操作數據和過程的時間延遲特性。
  17. Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology

    系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
  18. In this system, according to the performance requires of servo - system in rapid character, high precision, drive - stiffness and high - speed stability, we adopted a closed - loop control structure that includes three closed - loops : position closed - loop, speed closed - loop and current closed - loop

    根據伺服系統對快速性、高精度以及傳動的剛性和高的速度穩定性等方面的性能要求，系統採用了位置、速度、電流三閉環的控制結構。
  19. An upper bound of the closed loop performance statistic given by the index of quadratic performance is found for all admissible parameter uncertainties. the poles of the closed loop systems is described by the delta operator models in the specified stable region of the complex plane which makes the poles in the specified region when the sampling period is becoming shorter

    採用線性矩陣不等式處理方法及李亞普諾夫二次穩定性理論，分析、證明了極點約束控制的存在條件，並利用lmi方法把delta運算元系統的極點配置在一個穩定的區域內，解決了delta域內的極點配置問題，使得期望的極點始終在這個穩定的區域內。
  20. Despite the closed - loop performance advantages of multivariable controllers, decentralized controllers are widely used for its " simple structure, simplified design and good failure tolerance

    盡管多變量控制器有閉環控制性能的優勢，分散控制器由於其結構簡單、設計方便、容錯性好而得到了廣泛的應用。
分享友人
分享到 Line

分享到臉書