contents of resin 中文意思是什麼

contents of resin 解釋
含脂量
  • contents : 發言提綱
  • of : OF =Old French 古法語。
  • resin : n 樹脂;松脂;樹脂狀沉澱物。 resin opal 【礦物】脂光蛋白石。 acrylate [acrylic] resin 玻璃狀可塑...
  1. Abstract : based on the analysis of the main failures discovered in pavement on steel deck plate and the demanding service condition of the pavement on steel deck, high - temperature rutting test, low - temperature bending test and controlled stress flexural fatigue test are used to study the performance of asphalt mixtures modified by epoxy resin including high - temperature stability, low - temperature cracking - resistance, and fatigue cracking - resistance, which are served to evaluate the modification effect of epoxy resin of different contents. with the addition of epoxy resin, all the three performances are improved greatly. however, when the amount of epoxy resin added is over a certain value, the modification effect will be stable with no extra benefit detected. finally, in terms of the properties of the three respects, 20 ?, 30 ?, 30 ? are given separately as the proposal adding contents

    文摘:在分析鋼橋面鋪裝層主要病害和特殊工作環境的前提下,分別採用高溫車轍試驗、低溫小梁彎曲試驗和控制應力小梁彎拉疲勞試驗,研究了不同環氧樹脂摻量下的環氧樹脂改性瀝青混合料的高溫穩定性、低溫抗裂性和抗疲勞性能.試驗結果表明:環氧樹脂對這3個方面都有很大的改進效果,但改性效果和樹脂的添加量並不是一個無限遞增的關系,當添加量超過一定數值以後,改性的效果將趨于平穩.最後就高溫、低溫、疲勞3個方面分別提出環氧樹脂添加量為20 ? , 30 ? , 30 ?的建議值
  2. Based on the analysis of the main failures discovered in pavement on steel deck plate and the demanding service condition of the pavement on steel deck, high - temperature rutting test, low - temperature bending test and controlled stress flexural fatigue test are used to study the performance of asphalt mixtures modified by epoxy resin including high - temperature stability, low - temperature cracking - resistance, and fatigue cracking - resistance, which are served to evaluate the modification effect of epoxy resin of different contents. with the addition of epoxy resin, all the three performances are improved greatly. however, when the amount of epoxy resin added is over a certain value, the modification effect will be stable with no extra benefit detected. finally, in terms of the properties of the three respects, 20 ?, 30 ?, 30 ? are given separately as the proposal adding contents

    在分析鋼橋面鋪裝層主要病害和特殊工作環境的前提下,分別採用高溫車轍試驗、低溫小梁彎曲試驗和控制應力小梁彎拉疲勞試驗,研究了不同環氧樹脂摻量下的環氧樹脂改性瀝青混合料的高溫穩定性、低溫抗裂性和抗疲勞性能.試驗結果表明:環氧樹脂對這3個方面都有很大的改進效果,但改性效果和樹脂的添加量並不是一個無限遞增的關系,當添加量超過一定數值以後,改性的效果將趨于平穩.最後就高溫、低溫、疲勞3個方面分別提出環氧樹脂添加量為20 ? , 30 ? , 30 ?的建議值
  3. Aerospace series. carbon fibre laminates. determination of the fibre, resin and void contents

    航空航天系列.碳素纖維層壓材料.纖維.樹脂和空隙量的測定
  4. Carbon fibre laminates - determination of the fibre, resin and void contents

    碳纖維層壓板材.纖維樹脂含量和空隙率的測定
  5. With the modulus of elasticity as an index, the effects of glass fiber cloth, with the following conditions, were studied : various resin contents, addition of a silicone coupling agent, and resin spread at the interface between the veneer and the glass fiber cloth

    以楊木膠合板模板的彈性模量為指標,分析玻璃纖維布浸膠量、偶聯劑用量、玻璃纖維布上下面單板塗膠量等的影響。
  6. The resin contents are about the same for fractions of two feeds and increase gradually

    兩種油漿的膠質含量基本相同,且呈緩慢遞增趨勢。
  7. Macroporous adsorptive resin column and polyamide column were used respectively to purify arabinogalactan ( ag ) from larix gmeini rupr. the contents of impurity in ag and sugar varying with time were analyzed

    摘要分別採用大孔吸附樹脂柱層析和聚酰胺柱層析技術純化興安落葉松中的阿拉伯半乳聚糖,研究了兩種層析柱洗脫過程中的雜質含量、糖含量隨時間變化的情況,對比分析了它們對阿拉伯半乳聚糖的純化效果。
  8. Aerospace series - carbon fibre laminates - determination of the fibre -, resin - and void contents ; german version en 2564 : 1998

    航空航天系列.碳纖維層壓塑料.纖維含量樹脂含量和
  9. Influences of borate contents on the property of co2 - cured phenol - formaldehyde resol resin binder

    2固化甲階酚醛樹脂粘結劑性能的影響
  10. On the ground of researching of processing property of 3266 resins, the influence of tackifier contents on the flexural strength, shearing strength, and modulus of composites ( 3186 carbon cloth / 3266 resin and 827 carbon cloths / 3266 resin ) were also studied

    摘要在對3266樹脂工藝性研究的基礎上,研究了定型劑含量對3186緞紋、 827單向碳布3266樹脂基復合材料彎曲強度、層間剪切強度和模量的影響。
分享友人