control force characteristics 中文意思是什麼

control force characteristics 解釋
桿力特性曲線
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  • force : n 1 力，勢。2 體力，氣力，精力，魄力。3 暴力，壓力；兵力，武力。4 〈pl 〉 部隊，軍隊，兵力。5 勢...
  • characteristics : 產品性能描述
  1. The control force characteristics of manual-control system can be modified by the introduction of weights and springs.

    可以通過引進配重和彈簧來改善手控操縱系統的操縱力特性。
  2. B ) equivalent circuit method and finite element analysis ( fea ) to compute the static force are presented, the results obtained by each method are compared one with the other. c ) the results of dynamic simulation by means of the software, ansoft show the hlfm " s characteristics when the motor works in the special frequency and single stroke and the conditions used for position control. d ) the measured static thrust - displacement characteristics and the dynamic characteristics during starting show good correlation with the calculated results

    在設計並製作了實驗樣機的基礎上所做的研究內容包括； （ 1 ）分別用能量法和麥克斯韋張量法推導電磁力的計算公式，並討論他們的不同應用范圍； （ 2 ）分別用等效磁路法和有限元法作直線力電機的靜特性分析，並比較分析它們的計算結果； （ 3 ）用有限元模擬軟體做直線力電機動態特性的模擬，分別分析直線力電機的頻率特性、動子開合閘特性和開環位置控制的工作特性； （ 4 ）做直線力電機的靜推力?位移特性實驗和動子開合閘的動態實驗，並將實驗結果與計算結果進行對比，實驗驗證了計算模型及計算方法的正確性。
  3. It is the major task that how to take the advantage of digital control technology and use control algorithm to eliminate the surplus force as could as possible, and enhance the loading characteristics

    如何利用計算機數字控制的優點和特點，結合控制演算法的研究成果，最大限度的消除多餘力，提高加載性能是本文進行課題研究的重點內容。
  4. In order to realize smooth movement of mechanical system at a low velocity, the following work investigates new types of linear ultrasonic motors and antifriction technique by superposing the motor ’ s elliptical vibrating motion at the friction interface to change frictional characteristics, produce ultrasonic lubricant effect and realize active control of friction force

    本文研究新型超聲波馬達，利用其產生於摩擦界面的橢圓軌跡超聲振動引起的潤滑效應和摩擦接觸行為的改變來減小摩擦力的大小，完成對摩擦力的主動控制，實現機械繫統的低速平滑運動。
  5. The emphases of the research works of this thesis are laid on the mechanical performance of the shear connector of the continuous composite bridge, the crack status and design method for crack control of the concrete deck in the negative moment zone of the continuous composite bridge, the influence of the connecting rigidity and the construction method over the structural mechanical characteristics of the continuous composite bridge, and the force transmission mechanism and the stress distribution of the rigid node connecting the girder and the pier in the mixed bridge and so on

    其中重點研究了組合結構橋梁中剪力鍵性能，負彎矩區混凝土板裂紋狀態及控制裂紋的設計方法，鋼與混凝土的接合剛度和施工方法對結構受力特性的影響，以及混合結構橋梁中梁墩剛性連接的傳力途徑及應力分佈等。
  6. The reason of being widely accepted is attributed to the advanced management method, which suit the requirement of modern working force. this paper is based on the construction of production logistics and standard cost control system for wafangdian bearing group corporation. the concepts of production logistics in enterprise were presented ; the consistency between the infrastructure and characteristics of the production information was analyzed ; the significance of the production logistics management and the methods of constructing were illuminated

    Erp作為新一代企業管理信息系統的代表，之所以能夠得到廣泛認同，歸功于其先進的管理思想的確適應了目前社會生產力發展的步伐，本文以瓦房店軸承集團有限公司生產物流與標準成本控制系統的建設為背景，介紹了物流管理領域中企業生產物流的概念，分析了生產物流信息在構成及特點方面存在的一致性，闡述了生產物流管理的意義和生產物流管理系統的構建方法。
  7. Driving elements of fin stabilizer are designed and the simulation about characteristics of surplus force, loading system with or without disturbance, static or dynamic state is done. the relationship between the dynamic characteristics of servo valve and loading system " s control performance, loading gradient and loading system " s control performance is analyzed

    設計了減搖鰭電液負載模擬臺動力元件，利用相關軟體對加載系統多餘力特性、有擾及無擾特性、動態及靜態特性等控制性能進行了模擬分析，並分析了加載梯度、伺服閥動態特性與加載系統控制性能之間的關系。
分享友人
分享到 Line

分享到臉書