cooling curve 中文意思是什麼
cooling curve
解釋
步冷曲線-
Test method for determination of cooling characteristics of quenchants by cooling curve analysis with agitation drayton unit
通過攪拌冷卻曲線分析測定淬火劑冷卻特性的方法 -
Drayton standard test method for determination of cooling characteristics of quenchants by cooling curve analysis with agitation drayton unit
攪拌冷卻曲線分析法測定冷卻劑冷卻特性的標準試驗方法 -
This article choosed out organic phase change materials, and, the solid - liquid - equilibrium of eleven binary system including fatty alcohol / fatty acid, n - octadecane / fatty acid, n - octadecane / fatty alcohol system were determined by cooling curve, and, t - x phase diagrams of these systems were drawn. the result shows that all these systems are simple eutectic, at the same time, the entropy of phase change of every system in the eutectic point is determined by using differential scanning calorimetry ( dsc ). and n - octadecane / fatty acid systems were calculated theoretically
本文初選出部分有機相變貯能材料，採用步冷曲線法測定了12醇-羧酸系列、 18烷-羧酸系列、 18烷- 12醇體系共11組體系的二元固液相平衡關系，繪制了這11組體系的t - x相圖，測定結果表明，這幾組體系均為簡單低共熔體系；同時利用差熱掃描量熱法（ dsc ）對上面各組體系低共熔點處的相變焓進行了測定；並對18烷-羧酸系列進行了熱力學理論預測。 -
Test method for melting point of petroleum wax cooling curve
石油蠟熔點的試驗方法 -
Petroleum waxes ; determination of melting point cooling curve
石油蠟.熔點 -
Test method for determination of cooling characteristics of quench oils by cooling curve analysis
冷卻曲線分析法測定淬火油冷卻特性的方法 -
Standard test method for determination of cooling characteristics of quench oils by cooling curve analysis
通過冷卻曲線分析測定淬火油冷卻特性的標準試驗方法 -
Standard test method for melting point of petroleum wax cooling curve
石油蠟熔點的試驗方法 -
Adiabatic cooling curve
絕熱冷卻曲線 -
Methods of analysis of fats and fatty oils - physical methods - determination of cooling curve
脂肪和油脂分析方法.第1部分:物理法.第13節:冷卻曲線測定 -
This material has the ability in humidity absorbing and releasing and evaporate cooling. through theoretically analysis on this new building material - porosity moisture - conditioned material, a testing equipment is set up, the performance curve of the moisture - conditioned material ability in humidity absorbing and releasing and evaporate cooling is obtained, meanwhile, porosity moisture - conditioned material ' s validity to building energy efficiency design is proofed
在分析這種新型建築材料多孔調濕材料的理論分析基礎上，搭建了測試風道並進行了實驗研究，得出了調濕材料的自動吸放濕能力及蒸發冷卻性能曲線，證明多孔調濕材料對于建築節能設計的有效性。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
In chapter 4, for the first time, in the way of virtual malfunction simulation, cooling water of diesel engine type 4135 has been simulated under the stopping water supply malfunction. and the analysis and discussion has been taken on the result of transient temperature curve of the simulation. and in the same way, internally cooling oil piston of diesel engine type 180 has been numerically simulated on the virtual thermal loading mal
得出了虛擬其斷水故障模擬的瞬態溫度曲線結果，並對其進行了分析和探討；同時也用虛擬模擬的思想對180型柴油機內油冷活塞進行了虛擬其熱負荷故障的數值模擬，得出了其在斷油情況下和超負荷運轉情況下的分析結果。 -
In experimental research, the s - l - e of eleven binary system including fatty alcohol / fatty acid, n - octadecane / fatty acid, n - octadecane / fatty alcohol system were determined by cooling curve. at the same time, the s - l - e of one ternary system of n - octadecane / fatty acid / stearic acid was measured by pseudo - duality, and t - x phase diagrams of these systems were drawn
在實驗的研究中，採用步冷曲線法測定了12醇-羧酸系列、部分18烷-羧酸體系、 18烷- 12醇體系共11組體系的二元固液相平衡關系，同時採用擬二元法測定了18烷-硬酯酸-月桂酸體系的三元固液平衡關系，繪制了這12組體系的t - x相圖。 -
Technique of " a steel by line heating and cooling " have several characteristics such as full of techniques and difficulties etc, it is based on experience of experienced workers and use the fire heat steel plates in predetermined lines calculated by expert system, then cool them down by water, so the difference between forces of extention and contraction, the steel plates will curve to their desired shape
水火彎板是造船生產中技術性強、難度大，具有很強特色的一種經驗性鋼板曲面成形的熱冷加工工藝方法。這個項目就是和大連造船新廠合作的「大型復雜曲面鋼板水火加工智能機器人」 。 -
Continuous cooling transformation curve
連續冷卻轉變曲線 -
This software are compiled in vc + + computer language. the main function of the application is to calculate the load limitation of an air - cooling steam turbine - generator set under distinct flux of cooling water, environmental temperature and environmental wind speed, and the back pressure safeguard curve of the target steam turbine are considered
應用軟體以vc + +為開發平臺，考慮了特定汽輪機組的背壓保護曲線，通過計算空冷系統的熱力特性，實時給出當前環境溫度和環境風速以及循環水流量下機組的上限負荷，從而指導機組的運行。 -
Test method for determination of cooling characteristics of aqueous polymer quenchants by cooling curve analysis with agitation tensi method
通過攪拌冷卻曲線分析測定含水聚合淬火劑冷卻特性的方法 -
Tensi standard test method for determination of cooling characteristics of aqueous polymer quenchants by cooling curve analysis with agitation tensi method
用攪拌冷卻曲線分析法測定含水聚合物冷卻劑的冷卻特性的標準試驗方法
分享友人